If a 2 1/8 inch diameter medium carbon steel rod is to be turned between centers to a 2 inch diameter using high speed cutting bits without using a coolant, find the following:

Picture linked

Answer:

Computer science

Explanation:

Computer science is the most theoretical computing discipline, focusing mostly on finding new and better ways for computers to work.

The process of carrying out a specific computation through the design and construction of an executable computer program is known as computer programming.

Tasks like analysis, creating algorithms, and assessing the precision and resource use of those algorithms are all part of programming.

As we know,

The study of computing, robotics, and information is known as computer science. Algorithmic, computing theory, information theory, and automation are examples of academic areas in computer science.

Thus, computer science is the most theoretical computing discipline, focusing mostly on finding new and better ways for computers to work.

Learn more about computer programming here:

brainly.com/question/14618533

#SPJ2

Answer:

carried courage buried

Explanation:

its Filipino

Answer:

190$-200$

Explanation:

Answer:Modulus of Elasticity (E)-------- A

Explanation:

The modulus of elasticity, Young's modulus E is a measure of a material's stiffness or resistance to being elastically deformed when stressed or due to tension According to  Hook's law the modulus of elasticity is defined as the ratio of the stress to the strain and defined as the slope of its stress-strain region  in the stress and strain graph.

--The stiffer a material, the higher the elastic modulus and vice versa for a less stiff material.

it can be calculated with this formulae

Young’s modulus equation is E = tensile stress/tensile strain

= (FL) / (A X change in L)

where F = applied force,

L = initial length,

A = square area,

E = Young’s modulus in Pascals (Pa).

Answer:

i believe tungsten is stronger than titanium !

Answer:

  no

Explanation:

No. More power is dissipated when the transistor is in its active region. In general, transistors in switching circuits are biased either "on" or "off". Time spent in the active region is minimized.

_____

On the other hand, speed can be enhanced if the transistors are active. So, it's a speed/power trade-off. Usually power is of more interest, particularly when there are millions of switching circuits. However, in certain applications, speed may be the priority, so the transistor will be biased in its active region.

Answer:

72 MPa

Explanation:

Critical resolved shear stress = 36 MPa

calculate the maximum possible yield strength for a single crystal of the metal

first we have to express the critical resolved shear stress as

бy = 2т[tex]_{critical}[/tex]

given that the minimum stress needed to introduce yielding curve will occur  at Ψ = λ = 45

where : бy = yielding stress

             t[tex]_{critical}[/tex] = 36MPa

therefore the maximum possible yield strength

= (2) * (36)

= 72 MPa

Answer:

Mach number = 0.68168

The flow should be treated as compressible.

Explanation:

Given that:

The altitude of a commercial jet = 35000

The properties of air at that given altitude are as follows:

Pressure = 24.577 kPa

Temperature T = 50.78176° C

Temperature T = ( 50.78176 + 273 )K = 328.78176 K

[tex]\varphi = 0.38428 \ kg/m^3[/tex]

The velocity is also given as: 550 mph = 245.872 m/s

Therefore, the sonic velocity is firstly determined by using the formula:

[tex]a = \sqrt{ \vartheta \times R \times T\[/tex]

[tex]a = \sqrt{1.4 \times 287 \times 323.78176[/tex]

[tex]a = \sqrt{130095.5112[/tex]

a = 360.68755 m/s

Then, we can calculate the Mach number by using the expression:

[tex]{Mach \ number = \dfrac{V}{a}}[/tex]

[tex]Mach \ number = \dfrac{245.872}{360.68755}[/tex]

Mach number = 0.68168

b) Ideally, all flows are compressible because the Mach number is greater than 0.3, suppose the Mach number is lesser than 0.3, then it is incompressible.

Answer:

[tex]7304g/cm^3[/tex]

Explanation:

Density is the mass per unit volume, it is usually measured in kg/m³.

The density of a crystal structure is given by:

[tex]\rho=\frac{mass\ of\ atoms\ in\ unit\ cell}{volume\ unit\ cell} =\frac{nA}{V_cN_A} \\\\\rho=density, n= number\ of\ atoms/unit=1\ atom/unit\ cell,A=atomic\ weight=70.4\ g/mol,N_A=avogadro\ constant=6.023*10^{23}atoms/mol,V=volume=2R^3=[2(0.126*10^{-8})]^3cm\\\\\rho=\frac{1*70.4}{[2(0.126*10^{-8})]^3*6.023*10^{23}} =7304g/cm^3[/tex]

Answer:

7.307g/cm^3

Explanation:

The other guy is mostly right but his conversion factor was off. It should be 1.26x10^-8 on the bottom

Answer:

Well there are a lot of delicious food in the philppines but my most favorite is the Lechon, Adobo, Sisig, Chicken Curry, Crispy pata and Sinigang

Answer:

1) The pressure difference is 4.207 kilopascals.

2) 2.5 pounds per square inch equals 5.093 inches of mercury and 5.768 feet of water.

Explanation:

1) We can calculate the gas pressure difference from the U-tube manometer by using the following hydrostatic formula:

[tex]\Delta P = \frac{S\cdot \rho_{w}\cdot g \cdot \Delta h}{1000}[/tex] (Eq. 1)

Where:

[tex]S[/tex] - Relative density, dimensionless.

[tex]\rho_{w}[/tex] - Density of water, measured in kilograms per cubic meter.

[tex]g[/tex] - Gravitational acceleration, measured in meters per square second.

[tex]\Delta h[/tex] - Height difference in the U-tube manometer, measured in meters.

[tex]\Delta P[/tex] - Gas pressure difference, measured in kilopascals.

If we know that [tex]S = 1.5[/tex], [tex]\rho_{w} = 1000\,\frac{kg}{m^{3}}[/tex], [tex]g = 9.807\,\frac{m}{s^{2}}[/tex] and [tex]\Delta h = 0.286\,m[/tex], then the pressure difference is:

[tex]\Delta P = \frac{1.5\cdot \left(1000\,\frac{kg}{m^{3}} \right)\cdot \left(9.807\,\frac{m}{s^{2}} \right)\cdot (0.286\,m)}{1000}[/tex]

[tex]\Delta P = 4.207\,kPa[/tex]

The pressure difference is 4.207 kilopascals.

2) From Physics we remember that a pound per square unit equals 2.036 inches of mercury and 2.307 feet of water and we must multiply the given pressure by corresponding conversion unit: ([tex]p = 2.5\,psi[/tex])

[tex]p = 2.5\,psi\times 2.037\,\frac{in\,Hg}{psi}[/tex]

[tex]p = 5.093\,in\,Hg[/tex]

[tex]p = 2.5\,psi\times 2.307\,\frac{ft\,H_{2}O}{psi}[/tex]

[tex]p = 5.768\,ft\,H_{2}O[/tex]

2.5 pounds per square inch equals 5.093 inches of mercury and 5.768 feet of water.

Answer:

a) According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Explanation:

First, we need to determine the torque experimented by the shaft ([tex]T[/tex]), measured in kilonewton-meters, whose formula is described:

[tex]T = \frac{\dot W}{\omega}[/tex] (Eq. 1)

Where:

[tex]\dot W[/tex] - Power, measured in kilowatts.

[tex]\omega[/tex] - Angular velocity, measured in radians per second.

If we know that [tex]\dot W = 10\,kW[/tex] and [tex]\omega = 20.944\,\frac{rad}{s}[/tex], then the torque experimented by the shaft:

[tex]T = \frac{10\,kW}{20.944\,\frac{rad}{s} }[/tex]

[tex]T =0.478\,kN\cdot m[/tex]

Let consider that shaft has a circular form, such that shear stress is determined by the following formula:

[tex]\tau = \frac{16\cdot T}{\pi\cdot D^{3}}[/tex] (Eq. 2)

Where:

[tex]D[/tex] - Diameter of the shaft, measured in meters.

[tex]\tau[/tex] - Torsional shear stress, measured in kilopascals.

If we know that [tex]D = 0.03\,m[/tex] and [tex]T =0.478\,kN\cdot m[/tex], the torsional shear stress is:

[tex]\tau = \frac{16\cdot (0.478\,kN\cdot m)}{\pi\cdot (0.03\,m)^{3}}[/tex]

[tex]\tau \approx 90164.223\,kPa[/tex]

a) According to the maximum-shear-stress failure theory, we get that maximum shear stress limit is:

[tex]S_{ys} = 0.5\cdot S_{ut}[/tex] (Eq. 3)

Where:

[tex]S_{ys}[/tex] - Ultimate shear stress, measured in kilopascals.

[tex]S_{ut}[/tex] - Ultimate tensile stress, measured in kilopascals.

If we know that [tex]S_{ut} = 440\times 10^{3}\,kPa[/tex], the ultimate shear stress of the material is:

[tex]S_{ys} = 0.5\cdot (440\times 10^{3}\,kPa)[/tex]

[tex]S_{ys} = 220\times 10^{3}\,kPa[/tex]

Lastly, the static factor of safety of the shaft ([tex]n[/tex]), dimensionless, is:

[tex]n = \frac{S_{ys}}{\tau}[/tex] (Eq. 4)

If we know that [tex]S_{ys} = 220\times 10^{3}\,kPa[/tex] and [tex]\tau \approx 90164.223\,kPa[/tex], the static factor of safety of the shaft is:

[tex]n = \frac{220\times 10^{3}\,kPa}{90164.223\,kPa}[/tex]

[tex]n = 2.440[/tex]

According to the maximum-shear-stress failure theory, the static factor of safety of the shaft is 2.440.

b) According to the distortion-energy failure theory, we get that maximum shear stress limit is:

[tex]S_{ys} = 0.577\cdot S_{ut}[/tex] (Eq. 5)

If we know that [tex]S_{ut} = 440\times 10^{3}\,kPa[/tex], the ultimate shear stress of the material is:

[tex]S_{ys} = 0.577\cdot (440\times 10^{3}\,kPa)[/tex]

[tex]S_{ys} = 253.88\times 10^{3}\,kPa[/tex]

Lastly, the static factor of safety of the shaft is:

[tex]n = \frac{253.88\times 10^{3}\,kPa}{90164.223\,kPa}[/tex]

[tex]n = 2.816[/tex]

According to the distortion-energy failure theory, the static factor of safety of the shaft is 2.816.

Answer:

A) A mustache

B) A beard

Explanation:

A respirator is a device which is worn over the face to aid breathing through the use of oxygen. Because the fit is won on the face a mustache, or beard would change the fit of the respirator of the face as this would make the respirator tighter in some cases while in others not fit at all.

Answer: D) All of the above!

Explanation:

Answer:

Explanation:

I think I will say it is because most, if not all resistors have been made to standard already.

The value for the resistor that is chosen for two fixed arms from the Wheatstone Bridge have to be quite bear each other, as much as possible. The arm that moves and the other that doesn't move, their resistance values are made to be quite close as well. This makes the resistance of the arm that moves to be set somewhere in the middle, and as a result, the measurements don't exceed beyond the resistance range of the arm that moves.

I hope you understand?

Answer:

T = 3460 K

Explanation:

See attachment for calculation.

Since the temperature we have is above the melting point of the metal, then we can conclude that it is too high for the diffusion process to be possible.

Answer:

Speed V1 at the beginning of the skid  = 57.075 mph

Explanation:

Calculate the V1 speed at the beginning of the skid

V1 ( speed before brake was applied ) = ?

distance travelled by Vehicle 1 = 195 ft

curve tangent for vehicle 1 =  - 3% = - 0.03

coefficient of friction = 0.48

speed at Impact = 25 mph

To determine the V1 speed at the beginning of the skid we have to apply AASTHO

d1 = [tex]( \frac{VA^{2} - VA^{12} }{30(F+N)} )[/tex]

195 =  [tex](\frac{VA^2- 25^2}{30(0.48-0.03)} )[/tex]

Hence : VA = 57.075 mph

Answer:

The answer is below

Explanation:

Given that:

x = 5 cm = 0.05 m, width (w) = 5 cm = 0.05 m, thickness (t) = 1 mm = 0.001 m, k = thermal conductivity = 200 W/mK, h = heat transfer coefficient = 22 W/m².K, Tb = base temperature = 40°C, T∞ = 20°C

[tex]m=\sqrt{ \frac{hp}{kA} }=\sqrt {\frac{22*(2*0.05+2*0.001)}{200*(0.05*0.001)}} =15\ m^{-1}\\\\\frac{T-T_{\infty}}{T_b-T_{\infty}} =e^{-mx}\\\\\frac{T-20}{40-20} =e^{-15*0.05}\\\\T-20=9.45\\\\T=29.45^oC\\\\The\ rate\ of\ heat\ loss\ is:\\\\\dot{Q}=\sqrt{hpkA}(T_b-T_{\infty})\\ \\\dot{Q}=\sqrt{22*(2*0.05+2*0.001)*200*0.05*0.001}*(40-20)\\\\\dot{Q}=3\ W[/tex]

Answer:

Resolution of Fourier transform = 2Hz

Explanation:

Given:

Sample signals = 16,384 samples/second

Number of data points = 8,192 oints

Find:

Resolution of Fourier transform

Computation:

Resolution of Fourier transform = fs / N

Resolution of Fourier transform = 16,384 / 8,192

Resolution of Fourier transform = 2Hz

Answer:

The field strength needed is 0.625 T

Explanation:

Given;

angular frequency, ω = 400 rpm = (2π /60) x (400) = 41.893 rad/s

area of the rectangular coil, A =  L x B = 0.0611 x 0.05 = 0.003055 m²

number of tuns of the coil, N = 300 turns

peak emf = 24 V

The peak emf is given by;

emf₀ = NABω

B = (emf₀ ) / (NA ω)

B = (24) / (300 x 0.003055 x 41.893)

B = 0.625 T

Therefore, the field strength needed is 0.625 T

Answer:

The moment of inertia of the rotor is approximately [tex]1.105\times 10^{-6}[/tex] kilogram-square meters.

The rotor inertia may differ from these assumption due to differences in the shape of cross section.

Explanation:

We assume that rotor can be represented as a solid cylinder of radius [tex]r[/tex], length [tex]l[/tex], made of cooper ([tex]\rho = 8960\,\frac{kg}{m^{3}}[/tex]) and whose axis of rotation passes through its center of mass and is parallel to its cross section. By definition of Moment of Inertia and Theorem of Parallel Axes, the moment of inertia of the rotot is:

[tex]I = \frac{1}{4}\cdot \rho \cdot \left(\frac{\pi}{4} \right) \cdot R^{3}\cdot (3\cdot R^{2}+L^{2})[/tex]

[tex]I = \frac{\pi}{16}\cdot \rho \cdot R^{3}\cdot (3\cdot R^{2}+L^{2})[/tex] (Eq. 1)

Where:

[tex]\rho[/tex] - Density of copper, measured in kilograms per cubic meter.

[tex]R[/tex] - Radius of the rotor, measured in meters.

[tex]L[/tex] - Length of the rotor, measured in meters.

[tex]I[/tex] - Moment of inertia, measured in kilogram-square meters.

If we know that [tex]\rho = 8960\,\frac{kg}{m^{3}}[/tex], [tex]L = 25\times 10^{-3}\,m[/tex] and [tex]R = 8.98\times 10^{-3}\,m[/tex], the estimated moment of inertia of the rotor is:

[tex]I = \frac{\pi}{16}\cdot \left(8960\,\frac{kg}{m^{3}} \right)\cdot (8.98\times 10^{-3}\,m)^{3}\cdot [3\cdot (8.98\times 10^{-3}\,m)^{2}+(25\times 10^{-3}\,m)^{2}][/tex]

[tex]I \approx 1.105\times 10^{-6}\,kg\cdot m^{2}[/tex]

The moment of inertia of the rotor is approximately [tex]1.105\times 10^{-6}[/tex] kilogram-square meters.

From D'Alembert's Formula we know that net force of rigid bodies experimenting rotation equals the product of moment of inertia and angular acceleration. In this case, the purpose is minimizing moment of inertia and it is done by modifying the shape of the cross section so that rotor could be aerodynamically more efficient.

Answer:

It only detects errors if an odd number of bit flips have occurred.

Explanation:

Parity is a measure of how even or odd a string of digits (for example, a string of binary units is).  It is obtained by calculating the value of all the bits. Parity is used in error detection. A parity error is detected when the parity and the odd number of bits are incorrectly propagated.

A problem commonly associated with the parity bits is that they can only detect an odd number of bit errors. This means that if a digit is corrupted in the even binary digits there would be an incorrect detection of errors.

Answer:

True

Explanation:

True - because different classification of steel beam have different yield strength.

The moment capacity for a steel beam is given by;

M = Mn / Ωₙ

where;

M - the maximum moment acting on the beam

Ωₙ - is the Safety Factor for Elements in Bending = 1.67

Mn - nominal moment of the steel, given as

[tex]M_n = Z_x *f_y[/tex]

where;

Zₓ - the Plastic Section Modulus in the x or strong axis.

[tex]f_y -[/tex] is the Yield Strength of the Steel (A36W, A46 W or A50W)

A36W = 36 ksi

A46 W = 46 ksi

A50W = 50 ksi

Thus, before you calculate the moment capacity for a steel beam, you have to determine the classification of beam, for the yield strength of the steel beam.

Answer:

Option B: An MSDS

Explanation:

A dictionary is used to check up the meaning of general words and not for checking if a substance being used is hazardous. Option A is wrong.

MSDS means "Material Safety Data Sheet" and it contains documents with information that relates to occupational health & safety for checking various substances and products. Thus, option B is correct.

SAE stands for Society of Automotive Engineering and their standards pertain to mainly Automobiles. Thus option C is wrong.

EPA guidelines are mainly for checking facility and environmental health and safety compliance. Thus, option D is wrong.

Answer:

Your mobile phone has more computing power than the computers used for the Apollo 11 moon landing.

Mobile phones have to “work harder” to get a signal if you are in a moving vehicle.

The first mobile phone was made in 1973.

The first mobile phones that went on sale in 1983 cost nearly $4,000 each.

In 2012 Apple sold 340,000 phones per day.

4 out of 10 Brits admit to snooping on their partners phone.

Out of the 53% of snoopers that found incriminating evidence on their partner’s phone, 5% went on to terminate their relationship.

Waterproof mobile phones came to market because Japanese youngsters like to use them in the shower.

Apparently mobile phones have 18 times more bacteria on them than toilet handles!

Phubbing describes the act of snubbing someone by using your mobile phone in their company.

In 2015 more people died from taking selfies than shark attacks.

Teenagers that use a phone more than 2 hours a day increase their risk of depression and anxiety.

Nomobophobia is severe anxiety caused by the thought or act of losing your phone or running out of battery.

Explanation: