At which of the following points does a roller coaster have the most potential energy? As it is going down a hill. At the top of the hill. As it is climbing a hill. At the bottom of the hill.

Answer:

Explanation:36.05 km

Given

First car travels [tex]r_1=20\ km[/tex] South

then turns and travels [tex]r_2=30\ km[/tex] east

Suppose south as negative y axis and east as positive x axis

So, [tex]r_1=-20\hat{j}[/tex]

[tex]r_2=30\hat{i}[/tex]

Displacement is the shortest between initial and final point

Dispalcement[tex]=r=r_1+r_2[/tex]

Displacement[tex]=-20\hat{j}+30\hat{i}[/tex]

Displacement[tex]=30\hat{i}-20\hat{j}[/tex]

Magnitude [tex]=\sqrt{30^2+(-20)^2}[/tex]

Magnitude[tex]=36.05\ km[/tex]

Answer:

W= 20000j

Explanation:

W= fd = 1000N(20m) = 20000j

Answer:

640 J

Explanation:

ΔKE = KE − KE₀

ΔKE = ½ mv² − ½ mv₀²

ΔKE = ½ m (v² − v₀²)

ΔKE = ½ (80 kg) ((5 m/s)² − (3 m/s)²)

ΔKE = 640 J

Her kinetic energy increases by 640 J, so she does 640 J of work.

It's 640 for both answers. :)

Answer:

If you ground the flow of current like the last part of your question states you will not have a complete circuit as the circuit will open on a short circuit. To make a complete circuit operate you need a power source, an overload device to protect the conductors of the circuit, conductors to carry the current and a load across the power source which causes the current to flow in the circuit.

Explanation:

Leave any one of these things out and you will not have a complete circuit.

A complete electric circuit includes a voltage source, current, wires, and load to flow the current.

An electrical load can be described as an electrical component of a circuit that consumes electrical power such as electrical appliances, bulbs, and lights. The electrical load may also refer to the power consumed by a circuit. An electrical load is opposed to a power source, such as a battery, which produces power.

If an electric circuit contains an output port, a pair of terminals that generates an electrical signal, the circuit connected to this terminal is the load. Load influences the performance of circuits according to the output voltages or currents, such as voltage sources, and amplifiers.

Mains power outlets supply power at constant voltage, with electrical appliances connected to the power circuit making up the load. When a high-power device switches on, it drastically reduces the load impedance.

Learn more about electrical load, here:

https://brainly.com/question/28982413

#SPJ5

Answer:

I think your answer would be D

Explanation:

Answer:

hope this helps love! There are three methods of heat transfer: conduction, convection, and radiation. Cooking of food usually uses a combination of these methods. Conduction transfers the heat using direct contact; food is heated directly in a metal pan, in a liquid, or surrounded by air. ... The heat from the water is transferred to the egg.

Explanation:

When the water is heated, thermal expansion happens so the particles move farther apart and then the hot water moves up because it is less dense then the colder water. ... Convection is happening because when air is heated by the fire, the air becomes less dense and moves up because denser things sink.

Answer: I think it's 8,900

Explanation:because since you need to estimate it to the nearest thousand so 6,521 would be 7,000 and then 1,063 would be 1,000 and then 901would turn into 900 so then you add them all up and ur answer will be 8,900.

But I'm sorry if this was not the answer u were looking for

Answer:

Ionizing radiation is radiation with enough energy so that during an interaction with an atom, it can remove tightly bound electrons from the orbit of an atom, causing the atom to become charged or ionized. ... Forms of electromagnetic radiation.

(from google)

thank you :)

Ionizing radiation is radiation with enough energy that to remove tightly bound electrons from the orbit of an atom, causing that atom to become charged or ionized.

The process in which an electron is given enough energy to break away from an atom is called ionization.

This process results in the formation of two charged particles or ions:

Each ionization releases energy that is absorbed by material surrounding the ionized atom.

Ionizing radiation deposits a large amount of energy into a small area. In fact, the energy from one ionization is more than enough energy to disrupt the chemical bond between two carbon atoms.

There are three main kinds of ionizing radiation:

alpha particles, which include two protons and two neutrons

beta particles, which are essentially electrons

Therefore,

According to the definition of ionizing radiation,

Ionizing radiation can remove electrons from the atoms, i.e. It can ionize atoms.

Learn more about Ionizing radiation here:

https://brainly.com/question/26660482

#SPJ2

Answer:

So, Mercury is the closest planet to the Sun.

Explanation:

Answer:

Frictional force refers to the force generated by two surfaces that contacts and slide against each other.

~Hope this helps~ T^T

Answer

medium are much closer together

Explanation:

Sound travels fastest through solids. This is because molecules in a solid medium are much closer together than those in a liquid or gas, allowing sound waves to travel more quickly through it. In fact, sound waves travel over 17 times faster through steel than through air.

Answer:

318.3 nm

Explanation:

We approximate the circular film as a cylinder of height h and radius, r. Its volume V = πr²h. Since this volume equals the volume of the oil drop, the height of the circular film is thus h = V/πr²

V = 10⁻¹⁰ m³ and r = 10 m

Substituting into h, we have

h = 10⁻¹⁰ m³/π(10)²

= 0.3183 × 10⁻¹² m

= 3183 × 10⁻⁹ m

= 318.3 nm

Answer:

3N

Explanation:

Note that when an object is immersed in water it weighs less.

This means the weight seen is the apparent weight.

Now in water there is upthrust and is a counter force acting on the object and this force is opposite to the weight of the fluid alongside the container 10N

The apparent weight is the real weight - the upthrust

7N-10 = -3N

The essence of the negative sign is to show that this force is acting in opposite direction to the weight.

Note: the upthrust is 10N and it's opposite to the weight of the fluid and the tube on which the object on the force meter is subjected to.

Answer:

D.Oxygen has five valence electrons

Answer:

112.23 m

Explanation:

Displacement is the final position minus the initial position.

Δx = x − x₀

Δx = 100.1 m − (-12.13 m)

Δx = 112.23 m

Answer:

Time taken by birdie’s trip = 1.2235 s (Approx)

Explanation:

Given:

Velocity = 4.25 m/s

Displacement = 5.2 m

Find:

Time taken by birdie’s trip = ?

Computation:

⇒ Time taken = Displacement / Velocity

⇒ Time taken by birdie’s trip = Displacement / Velocity

⇒ Time taken by birdie’s trip = 5.2 m / 4.25 m/s

⇒ Time taken by birdie’s trip = 1.2235 s (Approx)

Answer:

the branch currents are as follows:

  top left: I2 = 0.625 A

  middle left: I1 = 2.500 A

  bottom left: I1-I2 = 1.875 A

  top center: I2+I3 = 2.500 A

  bottom center: I2+I3-I1 = 0 A

  right: I3 = 1.875 A

Explanation:

You can write the KVL equations:

Top left loop:

  I2(4) +(I2 +I3)(2) +I1(1) = 10

Bottom left loop:

  (I1-I2)(4) +(I1-I2-I3)(2) +I1(1) = 10

Right loop:

  (I2+I3)(2) +(I2+I3-I1)(2) = 5

In matrix form, the equations are ...

  [tex]\left[\begin{array}{ccc}1&6&2\\7&-6&-2\\-2&4&4\end{array}\right]\cdot\left[\begin{array}{c}I_1\\I_2\\I_3\end{array}\right] =\left[\begin{array}{c}10\\10\\5\end{array}\right][/tex]

These equations have the solution ...

  [tex]\left[\begin{array}{c}I_1\\I_2\\I_3\end{array}\right] =\left[\begin{array}{c}2.500\\0.625\\1.875\end{array}\right][/tex]

This means the branch currents are as follows:

  top left: I2 = 0.625 A

  middle left: I1 = 2.500 A

  bottom left: I1-I2 = 1.875 A

  top center: I2+I3 = 2.500 A

  bottom center: I2+I3-I1 = 0 A

  right: I3 = 1.875 A

_____

This can be worked almost in your head by using the superposition theorem. When the 5V source is shorted, the 10V source is supplying (I1) to a circuit that is the 4 Ω and 2 Ω resistors in parallel with their counterparts, and that 2+1 Ω combination in series with 1 Ω for a total of a 4Ω load on the 10 V source. That is, I1 due to the 10V source is 2.5 A, and it is nominally split in half through the upper and lower branches of the circuit. There is no current flowing through the (shorted) 5 V source branch.

When the 10V source is shorted, the 5V source is supplying a 4 +4 Ω branch in parallel with a 2 +2 Ω branch, a total load of 8/3 Ω. This makes the current from that source (I3) be 5/(8/3) = 15/8 = 1.875 A. There is zero current from this source through the 1 Ω resistor.

Nominally, the current from the 5V source splits 2/3 through the 2 Ω branch and 1/3 through the 4 Ω branch.

Using superposition, I2 = I1/2 -I3/3 = (2.5 A/2) -(1/3)(15/8 A) = 0.625 A. This is the same answer as above, without any matrix math.

  (I1, I2, I3) = (2.5 A, 0.625 A, 1.875 A)

__

It helps to be familiar with the formulas for resistors in series and parallel.

Answer:

circular motion is 2D

Explanation:

The circle is a two-dimensional (2D) shape. It only has two measurements, such as length and height, and is usually called a 'flat' shape. The ball, however, is a three-dimensional (3D) shape because it has three measurements (length, height, and width) and is sometimes called a 'solid' shape.

hope this helped

Explanation:

We have,

Mass of a box is 115 kg

Applied force is 424 N

It is required to find the frictional force of the floor on the box against you. Frictional force is an opposing force. It opposes the motion of an object. Here the applied force is 424 N. So, the frictional force has a magnitude of 424 N but it acts in opposite direction.

Answer:

[tex]\beta=B=8.05\mu T[/tex]

Explanation:

The density of the magnetic flux is given by the following formula:

[tex]\beta=\frac{\Phi_B}{A}=\frac{ABcos\theta}{A}=Bcos\theta[/tex]

The normal vector A and the vector of the magnitude of the magnetic field are perpendicular, then, the angle is zero:

The magnitude of the magnetic field is calculated by using the formula for B at a distance of x to a point in the plane of the loop:

[tex]B=\frac{\mu_oIR^2}{2(x^2+R^2)^{3/2}}[/tex]

For x = 0 you have:

[tex]B=\frac{\mu_oIR^2}{2R^3}=\frac{\mu_oI}{2R}[/tex]

R is the radius of the circular loop and its values is:

[tex]R=\sqrt{\frac{A}{\pi}}=\sqrt{\frac{0.5m^2}{\pi}}=0.39m[/tex]

Then, you replace in the equation for B with mu_o = 4\pi*10^-7 T/A:

[tex]B=\frac{(4\pi*10^{-7}T/A)(5A)}{2(0.39m)}=8.05*10^{-6}T=8.05\mu T[/tex]

and the density of the magnetic flux is

[tex]\beta=B=8.05\mu T[/tex]

Answer:

Potential energy = 1.6 J

Work done = -1.6 J

Explanation:

Potential Energy in the spring at this extension?

The potential energy U in the spring is U = 1/2kx² where k = spring constant = F/x where F = force = 20 N and x = extension = 0.16 m. So k = 20 N/0.16 m = 125 N/m

U = 1/2kx²

= 1/2 × 125 N/m × (0.16 m)²

= 1.6 J

What is the work done to extend the spring. 16 meters

Work done W = U₁ - U₂ where U₁ = initial potential energy = 0 and U₂ = final potential energy = 1.6 J

W = 0 - 1.6 J

   = -1.6 J

Kai weight on mars will be 203.5 N.

Gravitational field strength on Mars = 3.7 N/kg. (Given)

Mass = 55 kg. (Given)

Weight = Mass × Gravitational field strength

Weight = 55 kg × 3.7 N/kg

Weight = 203.5 N

Thus, we can conclude that Weight is the Gravitational force between the object and the planet.

Learn more about Weight here:

https://brainly.com/question/86444

#SPJ2

Answer:

358.9 (+/- 0.4) million years ago

Holocene Epoch, of the Quaternary Period

Devonian period

66 million years ago (prox)

521 million years ago

110,000 years ago

NW

North america became more cold when it moved NW

Explanation:

Answer:

A) 12.57 m

B) 5 RPM

C) 3.142 m/s

Explanation:

A) Distance covered in 1 Revolution:

The formula that gives the relationship between the arc length or distance covered during circular motion to the angle subtended or the revolutions, is given as follows:

s = rθ

where,

s = distance covered = ?

r = radius of circle = 2 m

θ = Angle = 2π radians  (For 1 complete Revolution)

Therefore,

s = (2 m)(2π radians)

s = 12.57 m

B) Angular Speed:

The formula for angular speed is given as:

ω = θ/t

where,

ω = angular speed = ?

θ = angular distance covered = 15 revolutions

t = time taken = 3 min

Therefore,

ω = 15 rev/3 min

ω = 5 RPM

C) Linear Speed:

The formula that gives the the linear speed of an object moving in a circular path is given as:

v = rω

where,

v = linear speed = ?

r = radius = 2 m

ω = Angular Speed in rad/s = (15 rev/min)(2π rad/1 rev)(1 min/60 s) = 1.571 rad/s

Therefore,

v = (2 m)(1.571 rad/s)

v = 3.142 m/s

The acceleration of the particle when it achieves its maximum displacement in the positive x-direction is 32 m/s²

To calculate the acceleration of the particle, we need to differentiate the expression for the velocity.

Given:

differentiate v with respect to t

When the particle achieves its maximum displacement,

Substitute these value of t into equation 1

Hence The acceleration of the particle when it achieves its maximum displacement in the positive x-direction is 32 m/s²

Learn more about acceleration here: https://brainly.com/question/605631

Answer:

Answer:

C

Explanation:

Velocity = velocity (initial) + acceleration*time.

More time - higher velocity.

Answer:

5m

Explanation:

The wavelength of a wave is the distance between successive trough or crest ;

Meaning that distance between successive trough is distance between trough and crest plus distance between crest and trough

Which is 2 times distance between trough and crest;

2×2.5= 5m

Answer:

8 mph

Explanation:

4 miles in half hour so you add 4 more for the second half

Answer:

a) B = 0.0151 T

b) [tex] \theta = 4.737 * 10^-^6 Tm^2 [/tex]

c) [tex] E = 7.896*10^-^4 [/tex]

d) [tex] = 60.4 T [/tex]

Explanation:

Given:

Diameter, d = 2.5 cm convert to meters = 0.025 m

Length, L = 30.0 cm convert to meters = 0.3 m

Number of turns, N = 300

Current, I = 12 A

a) Let's use the formula below to find the magnetic field.

[tex] B = \frac{u_0 N I}{L} [/tex]

[tex] B = \frac{4\pi * 10^-^7 * 300 * 12}{0.3} [/tex]

[tex] B = \frac{0.004524}{0.3} [/tex]

B = 0.0151 T

b) Given a radius, r = 1.00 cm, let's convert it to meters = 0.01 m

Let's use the formula below to find magnetic flux.

[tex] \theta = BA [/tex]

where [tex] A = \pi r^2 [/tex]

Therefore,

[tex] \theta = B \pi r^2 [/tex]

[tex] = 0.0151 \pi * (0.01)^2 [/tex]

[tex] \theta = 4.737 * 10^-^6 Tm^2 [/tex]

c) Given that the current in the solenoid uniformly goes from 12 A to 10 A in 0.001 seconds, the EMF generated will be:

[tex]E = \frac{- change in \theta}{change in t} = \frac{-u_0 N}{L} * \pi r^2 * \frac{change in I}{change in t}[/tex]

[tex] E = \frac{-4\pi * 10^-^7 * 300}{0.3} * \pi *(0.01)^2 * \frac{10 - 12}{0.001} [/tex]

[tex] -0.00125663 * \pi *(0.01)^2 * -2000[/tex]

[tex] E = 7.896*10^-^4 [/tex]

d) Let's use the formula:

[tex] \frac{u_m N I}{L} = 4000 \frac{u_0 NI}{L} [/tex]

[tex] 4000 * 0.0151 [/tex]

[tex] = 60.4 T [/tex]