A set of three resistors are set up in parallel. The resistor values are R1 = 3.0 Ohms, R2 = 11.0 Ohms, and R3 = 7.5 Ohms.
What is the total resistance of this circuit?
a
1.79 Ohms
b
0.60 Ohms
c
1.12 Ohms
d
2.97 Ohms

Answers

Answer 1

Answer:

A) 1.79ohms

Explanation:

Total resistance of resistors in parallel is given by ;

1/R = 1/R1 + 1/R2 +1/R3

Put in the values and make R the subject


Related Questions

Mousa builds a bike ramp at 22 degrees that allows him to just barely jump his bike across a 5 m wide stream in the local neighborhood. Bilyan wants to replicate Mousa’s jump by building his own ramp, but at a different angle. At what angle should Bilyan construct his ramp?

A.
44 degrees

B.
11 degrees

C.
78 degrees

D.
68 degrees

Answers

If Bilyan is trying to get over the 5m wide stream by double. He wants to construct his at 44 degrees because it’s double of 22. Hope that helps

How are amplitude modulation and frequency modulation techniques similar?
O Both are used by cell phones to produce images.
O Both transform electrical signals into sound waves.
O Both modify the pulse of a carrier wave.
O Both are used by radio stations to transmit sound.

Answers

Answer:

D. Both are used by radio stations to transmit sound.

Explanation:

How many peanut butter cups does Benny have if he has 2 times as many as Karen. Karen has 80 peanut butter cups.

Answers

Answer:

160 peanut butter cups

Explanation:

80 * 2 = 160

Answer:

160

Explanation:

if benny has 2x more than karen and karen has 80 you would multiply 80 by 2 to get 160. therefore benny has 160. hope that helps

4 facts about light waves

Answers

ray of light travels very fast. The speed of light in space is approximately 300 million metres per second. Light is a kind of energy that can move in waves and it is made up of a flow of small particles of energy called photons. A ray of light travels very fast.

Michael is training to join the Army and runs to the left with a constant
velocity of 2 m/s. If he starts at Om, what is his position after 5 seconds?
Don't forget units and directions if appropriate.
Your answer

Answers

Answer:

[tex]10 \: m.[/tex]

Explanation:

[tex]his \: position \:is \: his \: distance \: from \: the \: \\ point \: of \: motion \: and \: is \: given \: by : \\ v = \frac{s}{t} \\ s = vt =2 \times 5 \\ s = 10 \: m.[/tex]

If a car moves with a constant acceleration, can you conclude that there are no forces acting on it?

Answers

There are forces acting on it

Obtain 5 pennies. Line up 3 pennies touching in a perfect line. Line up 2 more pennies touching each other in perfect line with the other 3 pennies. Leave some space between the groups of pennies. Place your fingers onto the 2 slider pennies. Slide the 2 pennies into the group of 3. This may take practice to slide them correctly. Record what happens to the pennies after collision.

Answers

Answer:

Two other pennies will be launched, resting only 3 pennies left.

Explanation:

Take "o" as a pennie.

ooo    oo

ooo ← oo

ooooo

oo ← ooo

The process is very similar to what occurs with the pendulum of newton by the law or principle of energy conservation.

In physics, the law or principle of energy conservation states that the total amount of energy in an isolated system remains constant. Such a principle is closely linked to the very definition of energy. An informal way of enunciating this law is to say that energy cannot be created or destroyed: energy can only be transformed from one type to another. The energy from the two pennies will be transferred to the other two pennies from the edge, the energy is then transformed into a kinetic move again.

The frictional force on moving Toyota Prius is - 259.7 N. Using the calculated net force from problem 4, determine the force of the engine needed to cause the acceleration. Show your work.

Answers

Complete Question

The frictional force of moving Toyota Prius was given as  - 259.7 N. net force was 795 N and determined the force of the engine needed to cause the acceleration

Answer:

The value is [tex]F_e = 1054.7 \ N[/tex]  

Explanation:

From the question we are told that

   The frictional force is  [tex]F_f = -259.7 \ N[/tex]

   The net force is  [tex]F_{net} = 795 \ N[/tex]

Generally the net force is mathematically represented as

     [tex]F_{net} = F_e - F_f[/tex]

=>   [tex]F_e = F_{net} - F_f[/tex]

=> [tex]F_e = 795 - [-259.7][/tex]

=> [tex]F_e = 1054.7 \ N[/tex]    

   

A pitcher throws a baseball horizontally with a speed of 42 m/s. If the pitcher throws the baseball from a height of 1.25 meters, what is the resultant velocity of the ball right before it hits the ground? Include direction (angle).

Answers

Answer:

v = 42.28 m/s

Explanation:

It is given that,

The horizontal speed of a baseball, [tex]u_x=42\ m/s[/tex]

The pitcher throws the baseball from a height of 1.25 meters, h = 1.25 m

Firstly finding t i.e. the stone takes to reach the ground. Using second equation of motion as follows :

[tex]d=ut+\dfrac{1}{2}at^2[/tex]

a = -g and u = 0

[tex]d=-\dfrac{1}{2}gt^2\\\\t=\sqrt{\dfrac{-2d}{g}} \\\\t=\sqrt{\dfrac{-2\times 1.25}{9.8}} \\\\t=0.5\ s[/tex]

Vertical component of the velocity is :

[tex]v_y=gt\\\\v_y=9.8\times 0.5\\\\v_y=4.9\ m/s[/tex]

Resultant velocity,

[tex]v=\sqrt{v_x^2+v_y^2} \\\\v=\sqrt{42^2+4.9^2} \\\\v=42.28\ m/s[/tex]

So, the resultant velocity of the ball before it hits the ground is 42.28 m/s.

Answer:

42.28 m/s

Explanation:

You are writing a story on a table. What physical properties would you want your table to have?

Answers

Answer:The Table should be smooth, hard, and large

Explanation:

what are these things called​

Answers

Wavelength and crest

Hope I helped

An elephant walks due east for a distance of 7.9 km, turns around and then goes due west for 1.9 km, and finally turns around again and heads 3.6 km due east. What is the displacement traveled by the elephant in meters?

Answers

Answer:

The displacement traveled by the elephant is 9600 east

Explanation:

Displacement is defined as an object's change in position which is given by the difference between final and initial location of the object

The displacement of the elephant are, taking east as positive direction of motion;

1) 7.9 km east = + 7.9 km

2) 1.9 km west = -1.9 km

3) 3.6 km east = 3.6 km

The net (sum) displacement of the elephant, ∑Δx is given as follows;

∑Δx = 7.9 km - 1.6 km + 3.6 km = 9.6 km

Given that the sum of the displacement is positive and that 9.6 km = 9600 m, we have;

The displacement traveled by the elephant = ∑Δx =  9600 east.

While hiking in the mountains, you see a mountain lion. If you were to react as the Cannon–Bard theory of emotions proposes, which sequence of events would characterize your response? Group of answer choices You would experience physiological changes and a feeling of fear simultaneously. You would feel fear followed by physiological changes. You would experience physiological changes followed by fear. You would experience physiological changes and context appraisal followed by fear

Answers

Answer:

You would experience physiological changes and a feeling of fear simultaneously.

Explanation:

Cannon–Bard theory of emotions can as well be regarded as Thalamic theory of emotion, whenever the body experience a stimuli, a message will be sent to the brain by the Thalamus then there will be emotions as a result of this a physiological reaction such as trembling, sweating and others would follows. The theory stressed that physical reaction doesn't depends on emotional reaction.

In the case of hiking in the mountains, and one see a mountain lion. If one were to react as the Cannon–Bard theory of emotions proposes, the sequence of events that would characterize One's response is one would experience physiological changes and a feeling of fear, because a message is send to the brain by the Thalamus, then emotion set in and physiological reaction, which explains Cannon–Bard theory.

There are 3 batteries in a series circuit, each containing 9V, and the total current is 1.5 A. Along the circuit is 4 resistors. The first is 3 ohms, the second is 6 ohms, the third is unknown, and the fourth is 5 ohms. What is the voltage drop across the unknown resistor

Answers

Answer:

The voltage drop across the unknown resistor is 6 volts.

Explanation:

Given;

the current flowing in the series circuit, I = 1.5 A

number of batteries in the series circuit, = 3

voltage in each battery = 9V

total voltage in the circuit, 3 x 9V = 27 V

number of resistor in the circuit, = 4

R₁ = 3 ohms

R₂ = 6 ohms

R₃ = ?

R₄ = 5 ohms

Determine the total resistance in the circuit by applying Ohms law;

V = IR

R = V / I

R = 27 / 1.5

R = 18 ohms

Determine the unknown resistance;

R₁ + R₂ + R₃ + R₄ = 18 ohms

3 + 6 + R₃  + 5 = 18

R₃ = 18 - 14

R₃  = 4 ohms

The voltage drop across the unknown resistor (R₃  = 4 ohms);

V₃ = IR₃

V₃ = 1.5 x 4

V = 6 volts.

Therefore, the voltage drop across the unknown resistor is 6 volts.

An object is moving to the left. In which direction would a force need to be exerted to make this object slow down?

Answers

Answer:

left

Explanation:

When a force is applied in the opposite direction of motion, it opposes the motion of the object, causing its speed to decrease.

What is force?

A force is an influence in physics that can change the motion of an object. A force can cause a mass object to change its velocity, or accelerate.

Intuitively, force can be described as a push or a pull. A force is basically a vector quantity as it has both magnitude and direction.

The term "force" has a specific meaning in science. At this level, it is perfectly acceptable to refer to a force as a push or a pull.

Another object applies a force to another. The concept of a force is not restricted to living or non-living things.

To slow a moving object, apply force in the opposite direction to the direction of motion.

Thus, the force should be applied from left to slow down the object.

For more details regarding force, visit:

https://brainly.com/question/13191643

#SPJ2

A scientific
a. theory
b. law
is a rule used to describe a pattern seen in nature, not an explanation of why that pattern might occur.
C. system
d. sequence
Please select the best answer from the choices provided
Ο Α
О В
О с
OD

Answers

I think the answer is c

a scientific LAW is the answer

Explanation:

a scientific law is the rule that nature runs by.

Which combination of processes from the water cycle is most likely to cause flooding? low runoff, low evaporation high runoff, high precipitation high runoff, low precipitation low runoff, high condensation

Answers

Answer:

High run off, low evaporation

Explanation:

High run off and low evaporation causes flood because if evaporation is low, there won't be changing of liquid water to gas or vapor meaning water will be in abundance and if there is much water in abundance it can lead to flooding. High run off can result in flooding if rainfall water overwhelm the capacity of the drainage system i.e the water is more than what the drainage system can carry, it can result in flooding.

Answer:

high runoff, low evaporation, low precipitation

Explanation:

High run off and low evaporation causes flood because if evaporation is low, there won't be changing of liquid water to gas or vapor meaning water will be in abundance and if there is much water in abundance it can lead to flooding. High run off can result in flooding if rainfall water overwhelm the capacity of the drainage system i.e the water is more than what the drainage system can carry, it can result in flooding.

What shape must you make with a wire in a circut to have that current generate a magnetic field that is identical to the magnetic field produced by a normal bar magnet?
a
A straight line
b
An oval
c
A square
d
A coil

Answers

Answer:

The correct option is;

d. A coil

Explanation:

When a wire, which is an electric conductor is formed into the shape of a coil, and current is allowed to flow through the wire coil, a magnetic field is generated

The magnetic field generated by the electromagnetic coil has direction that consists of flux emanating from one end of the coil and entering the coil from the other end, similar to that of the magnetic field produced by a normal bar magnet.

Answer:

The maximum speed an object can fall in the presence of air resistance

Newton's third law

A coil

(a) Write down the Bernoulli's Equation and continuity Equation for a pipe flow and define each term in the equation. (b) The closed tank of a fire engine is partly filled with water, the air space above being under pressure. A 6 cm bore connected to the tank discharges on the roof of a building 2.5 m above the level of water in the tank. The friction losses are of 45 cm of water. Determine the air pressure which must be maintained in the tank to deliver 20 litres/sec on the roof.

Answers

Answer:

A) [tex]\frac{P}{p} + \frac{1}{2} v^2 + gh = k\\[/tex]

B )  53.9 kN/m^2

Explanation:

a) Bernoulli's equation and continuity equation  for a pipe flow

[tex]\frac{P}{p} + \frac{1}{2} v^2 + gh = k[/tex]

[tex]\frac{P}{p}[/tex]  = pressure head

[tex]\frac{1}{2}v^2[/tex] = velocity head

gh = potential head

k = constant

p = density

b) determine the air pressure that must be maintained

Given data :

Discharge rate( R ) = 20 liters/sec ≈ 0.02 m^3

Bore diameter ( d ) = 0.06 m

first we calculate the velocity in the 6 cm  bore

v = [tex]\frac{R }{\frac{\pi }{4} *d^2}[/tex]   ------- (2)

R = 0.02

d = 0.06

insert the given values into equation 2

V = 7.07 m/s

next we apply the Bernoulli's equation by rewriting it as follows

[tex]\frac{P}{pg} + \frac{1}{2g} v^2 + h = k[/tex]

[tex]\frac{1}{2g}v^2[/tex] ( velocity head ) = [tex]\frac{7.07^2}{2*9.81}[/tex]  = 2.55

next  we will apply the use of energy conservation law on the surface of water  in tank and that on the roof :

Note : H1(frictional head loss ) = 45cm = 0.45 m , g = 9.81

applying the energy conservation  law

[tex]\frac{P1}{pg} + \frac{1}{2g} v_{1} ^2 + h1 =[/tex] [tex]\frac{P2}{pg} + \frac{1}{2g} v_{2} ^2 + h2[/tex]

[tex]\frac{P1}{pg}[/tex]  = 0 + 2.55  + 2.5 + 0.45

therefore ; P1 = 9.81 * 5.55 = 53.9 kN/m^2

El elevador hidráulico de un garaje funciona mediante una prensa hidráulica conectada a una toma de agua de la red urbana que llega a la máquina con una presión de 5x10 5 N/m 2 . Si el radio del émbolo es de 20 cm y el rendimiento es de un 90% ¿Cuál es el valor en toneladas de la carga que como máximo puede levantar el elevador.

Answers

Answer:

El elevador puede levantar 5.76 toneladas de carga máxima.

Explanation:

De acuerdo a la ley de Pascal:

[tex] p_{1} = p_{2} [/tex]          

[tex] \frac{F_{1}}{A_{1}} = \frac{F_{2}}{A_{2}} [/tex]   (1)

En donde:

F: es la fuerza

P: es la presión

A: es el área

Sabiend que p₁ = 5x10⁵ N/m², tenemos que F₂ es:                              

[tex] F_{2} = p_{1}A_{2} [/tex]       (2)

El área del embolo viene dada por el área de una circunferencia:  

[tex] A_{2} = \pi r^{2} [/tex]    (3)

Introduciendo la ecuación (3) en la ecuación (2) tenemos:

[tex] F_{2} = p_{1}\pi r^{2} = 5 \cdot 10^{5} N/m^{2} \pi (0.20 m)^{2} = 62832 N [/tex]

Dado que el rendimiento es del 90%, la fuerza máxima es:

[tex] F_{2} = 62832 N*0.90 = 56549 N [/tex]

Ahora sabemos que la fuerza del elevador para levantar la carga máxima  es 56549 N y para encontrar el valor de toneladas de la carga máxima que puede levantar el elevador, debemos encontar la fuerza necesaria para levantar 1 tonelada:          

[tex] F = mg = 1000 kg*9.81 m/s^{2} = 9810 N [/tex]  

Finalmente, si para levantar 1 tonelada se debe aplicar una fuerza de 9810 N, y la fuerza total es igual a 56549 N, el numero de toneladas que puede levantar el elevador es:      

[tex] N = \frac{F_{2}* 1 ton}{F} = \frac{56549 N* 1 ton}{9810 N} = 5.76 ton [/tex]

Por lo tanto, el elevador puede levantar 5.76 toneladas de carga máxima.

Espero que te sea de utilidad!

If the deflection of a spring is doubled, then how much does the force change?

Answers

Answer:

The force is doubled as well.

Explanation:

If you double the spring then the force doubles as well.

If the deflection of the spring is doubled, the force exerted by the spring will also be doubled.

What is the Hooke's Law?

The relationship between the deflection of a spring and the force it exerts is described by Hooke's Law, which states that the force exerted by a spring is directly proportional to its deflection. Mathematically, this can be expressed as:

F = kx

where F is the force exerted by the spring, x is the deflection of the spring, and k is the spring constant, which represents the stiffness of the spring.

If we double the deflection of the spring, then x becomes 2x, and the force exerted by the spring becomes:

F = k(2x) = 2kx

Thus, if the deflection of the spring is doubled, the force exerted by the spring will also be doubled (assuming the spring constant remains constant).

Learn more about the deflection here:

https://brainly.com/question/28334742

#SPJ6

A crate is being pushed with a force of 75 N, if the resulting acceleration of the crate is 3 m/s? what is the
mass of the crate?

Answers

Answer:

The answer is 15 kg

Explanation:

The mass of the crate can be found by using the formula

[tex]m = \frac{f}{a} \\ [/tex]

f is the force

a is the acceleration

From the question we have

[tex]m = \frac{75}{3} \\ [/tex]

We have the final answer as

15 kg

Hope this helps you

PLEASE HELP ME!


Which statement about nuclear reactions is NOT true?
a.
Nuclear power plants use fission of uranium.
b.
In fission, the total mass of the reactants equals the total mass of the products.
c.
In fission, nuclei are split, and in fusion, nuclei are combined.
d.
Energy as heat and light in the sun are generated by hydrogen fusion reactions.

Answers

Answer:

b.  In fission, the total mass of the reactants equals the total mass of the products.

Explanation:

In a nuclear reaction, the total mass of the reactants does not equal to the total mass of the products.

This is because mass is converted to energy in a nuclear reaction.

It is true that nuclear power plants use fission. Uranium is the fuel in most reactors used to generate electricity. During nuclear fission, an unstable nucleus is split and in fusion, atoms are combined together. Heat and light is produced in the sun which are generated by hydrogen fusion reactions.

does anybody know?? Please help

Answers

Step 1;
Resolve or break the motion into horizontal and vertical components along the x- and y- axes.

Step 2;
Treat the motion as two independent one-dimensional motions, one horizontal and the other vertical

Step 3;
Solve for the unknowns in two separate motions—one horizontal and one vertical

Step 4; Recombine the two motions to find the total displacements and velocity v.

If two objects crash into each other, what happens? Are both objects affected? How? If you can, give an example to support your ideas.

Answers

In a collision between two objects, both objects experience forces that are equal in magnitude and opposite in direction. Such forces often cause one object to speed up (gain momentum) and the other object to slow down (lose momentum).

If two objects crash into each other, they experience collision and both bodies are affected.

Two bodies are said to collide if they hit or crash into each other.

Hence when two objects crash into each other;

collision occursThere is a release of energy due to this collisionOne of the objects tends to gain momentum or speed while the other object loses momentum.

For example, two rolling objects going in opposite directions when they hit each other tens to experience a collision.

Hence we can conclude that if two objects crash into each other, they experience collision and both bodies are affected.

Learn more here: https://brainly.com/question/20424486

On release 1, a student releases a cart from the top of a ramp, such that the cart travels 190cm before hitting the stopper. The cart increases speed steadily and reaches the bottom of the ramp in 4.00s. What was the magnitude of the cart's acceleration on release 1?

Answers

Answer:

0.2375m/s²

Explanation:

Given

S = 190cm = 1.9m

initial velocity u = 0m/s

Time t = 4.00s

Required

acceleration

Using the equation of motion

S = ut + 1/2at²

Substitute

1.9 = 0+1/2a(4)²

1.9 = 8a

a = 1.9/8

a = 0.2375m/s²

The magnitude of the cart's acceleration is 0.2375m/s²

A race car accelerates uniformly from 19.5 m/s to 50.1 m/s in 2.47 seconds. Determine
the acceleration of the car and the distance traveled.

Answers

Answer:

12.4m/s²; 80.99m

Explanation:

Acceleration can be defined as the rate of change of the velocity of an object with respect to time.

This simply means that, acceleration is given by the subtraction of initial velocity from the final velocity all over time. Hence, if we subtract the initial velocity from the final velocity and divide that by the time, we can calculate an object’s acceleration.

Mathematically, acceleration is given by the equation;

[tex]Acceleration (a) = \frac{final \; velocity - initial \; velocity}{time}[/tex]

Given the following data;

Initial velocity = 19.5m/s

Final velocity = 50.1m/s

Time = 2.47 secs

Substituting into the equation;

[tex]a = \frac{50.1 - 19.5}{2.47}[/tex]

[tex]a = \frac{30.6}{2.47}[/tex]

Acceleration, a = 12.4m/s²

Solving for the distance covered;

[tex] S = ut + \frac {1}{2}at^{2}[/tex]

Substituting into the values into the equation;

[tex] S = 19.5(2.47) + \frac {1}{2}(12.4)(2.47)^{2}[/tex]

[tex] S = 48.165 + 6.2 *6.1009[/tex]

[tex] S = 48.165 + 32.8256[/tex]

S = 80.99m

help pls ill give points​

Answers

Answer:

The answer Is erosion!

Hope you do Great!

Explanation:

Answer:

weathering

Explanation:

How does the sun works

Answers

Answer:

The sun works by nuclear fission, because there is so much pressure, it makes it vErY hOt. ( About 10,340 degrees Fahrenheit to be exact, or 5,726 degrees Celsius* )

Explanation:

Hope this helps! <3

Is the moon accelerating?

Answers

Answer:

The Earth's gravity keeps the Moon orbiting us. ... This means gravity makes the Moon accelerate all the time, even though its speed remains constant.

Yes it is always accelerating due to gravity
Other Questions
(HELP ASAP PLEASE) What is the image of (4, -2) after a dialation of 3 A rocket is shot out of a navy battleship to test a new rocket. It takes 16 seconds for the rocketto reach its destination after leaving the barrel. If its final velocity was found to be 200 m/s,then what was the rocket's acceleration?A. 8m/s squaredB. 12 m/s squaredC. 12.5 m/s squaredD. 16m/s squared ILL GIVE BRAINLIEST Help me!!!Cuando compras pagas en la liquidacionTrue or false When does genetic mutation occur Find the zeroes of the polynomial f(x)= 2x - 5x + 3 and verify the relationship between the zeroes and the coefficients. What properties of an element are affected by electron distribution?=Define malleability.Define ductility.State one reason gold is used in jewelry.Why is mercury no longer used in many devices?What are the properties of nonmetals?List the states of matter in which nonmetals can exist and give one example of each state.What are the physical properties and uses of sulfur?What are the physical properties and uses of bromine?What are the physical properties and uses of helium?Define metalloid.Why would it be difficult to decide whether or not an element was a metalloid based on its properties?Why is silicon used extensively in electronics?What are borosilicates used for?Why is the use of arsenic as an insecticide decreasing?What is a main application of antimony? Find the Unit Rate: 300 miles in 5 hours Carbon atoms typically makebond(s) in a molecule.afourb threeconedtwoChat which of the following is a gas. Traits are determined by the sequence of nucleotides in DNAOTrueO False WHO iS iN My SwAmP It Better Not Be youz!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! What are measures of 21 and 22? A car started its motion from rest and accelerated for 6 seconds, with the acceleration of 4 m/s2. Then it decelerated for 5 seconds, with the acceleration of -1.6 m/s2. What was the velocity of the car after 6+5 seconds? I NEED LOTS OF HELP ON THIS Can someone help me please, I think it may be B but i'm not sure.. Bee Stings:What are symptoms that a sting has occurred?How would the symptoms be different if this was an allergic reaction to a bee sting?What is the treatment for bee stings? (Name at least three steps to treatment).What should you do for treatment for an allergic reaction to a bee sting? In the United States, alcoholic beverages that are sold in stores display a government warning stating that pregnant women should not drink alcoholic beverages. This is because it prevents cleavage division from occurring, so a zygote cannot become a blastocyst. if a woman drinks alcohol while she is pregnant, she may not be able to ovulate again after childbirth. studies have proven that alcohol consumption causes long-lasting disorders in the fetus. the science of chemistry has shown that alcohol is a reactive substance that may interfere with the mothers food digestion. 2. A 60 kg crate is being lowered from a loading dock to the floor of a warehouse by a thick rope. The rope exerts a constant upward force of 500 N as it is descending to the floor. a) Draw a free-body diagram for the crate. b) Calculate the acceleration (if any) of the crate. imperial china, place the following events in order ANSWER QUESTION 1 THROUGH 2 AND SHOW HOW YOU GOT YOUR ANSWER.(1) A farm has 15 rows of fruit trees with 7 trees in each row. The last 4 rows of trees are cherry trees. The remaining trees are orange trees. How many orange trees are on the farm?(2) At the bakery, there are 5 rows with 12 chocolate chip cookies on each tray. There are 2 trays with 14 cookies on each tray. If 7 cookies are sold. How many cookies are left? A major criticism of the electoral college is that it(1) limits the influence of the two-party political system(2) allows a president to be elected without a majority ofthe popular vote(3) forces each political candidate to campaign in every(4) makes the federal election process too expensive