In order to determine how many coulombs are in a typical car battery's 70 amp-hours of charge, we first need to understand the relationship between amps and coulombs.
Amps measure the flow of electric current, while coulombs measure the amount of electric charge. One coulomb is equal to the amount of charge transported by a current of one ampere in one second.
Therefore, to convert amp-hours to coulombs, we need to multiply the number of amp-hours by the number of seconds in an hour (3,600) and by the number of coulombs per ampere-second (1). This gives us:
70 amp-hours x 3,600 seconds/hour x 1 coulomb/ampere-second = 252,000 coulombs
So a typical car battery provides 252,000 coulombs of charge. This is important information because it helps us understand the amount of electrical energy available for use in the various components of the vehicle, such as the headlights, windshield wipers, and sound system.
The alternator plays a critical role in maintaining and replenishing the charge on the car's battery, which in turn ensures that these components can continue to operate effectively.
Overall, the interplay between mechanical and electrical systems in a motor vehicle is a fascinating and complex topic that requires a deep understanding of physics, engineering, and technology.
To know more about coulombs refer here
https://brainly.com/question/12498766#
#SPJ11
Two blocks of masses 1. 0 kg and 2. 0 kg, respectively, are pushed by a constant applied force f across a horizontal frictionless table with constant acceleration such that the blocks remain in contact with each other, as shown above. The 1. 0 kg block pushes the 2. 0 kg block with a force of 2. 0 n. The acceleration of the two blocks is.
The acceleration of the two blocks is approximately [tex]0.67 m/s^2.[/tex]
Since the two blocks are in contact and moving together, they are considered as a single system.
The net force on the system is the force applied to the 1.0 kg block minus the force of friction between the two blocks. According to Newton's second law, the net force is equal to the mass of the system times its acceleration:
Net force = (mass of system) x (acceleration)
We can set up an equation for the net force as follows:
Net force = F - f
where F is the applied force, and f is the force of friction between the two blocks. Since the table is assumed to be frictionless, there is no frictional force, so f = 0.
Therefore, the net force is simply equal to the applied force F:
Net force = F
We can now substitute the values given in the problem:
F = 2.0 N (the force applied to the 1.0 kg block)
m = 1.0 kg + 2.0 kg = 3.0 kg (the total mass of the system)
Using the equation for the net force, we can find the acceleration of the system:
Net force = (mass of system) x (acceleration)
F = m x a
a = F / m
a = 2.0 N / 3.0 kg
[tex]a =0.67 m/s^2[/tex]
To know more about acceleration refer here
https://brainly.com/question/12550364#
#SPJ11
A 120-kg refrigerator that is 2. 0 m tall and 85 cm wide has its center of mass at its geometrical center. You are attempting to slide it along the floor by pushing horizontally on the side of the refrigerator. The coefficient of static friction between the floor and the refrigerator is 0. 30. Depending on where you push, the refrigerator may start to tip over before it starts to slide along the floor. What is the highest distance above the floor that you can push the refrigerator so that it will not tip before it begins to slide?.
You can push the refrigerator up to a height of 3.33 m above the floor without it tipping over before it starts to slide.
To determine the highest distance above the floor that you can push the refrigerator so that it will not tip before it begins to slide, we need to find the point where the gravitational force acting on the refrigerator produces a torque that is equal and opposite to the torque produced by the force of friction when it is about to tip over.
First, we need to calculate the gravitational torque on the refrigerator. The gravitational force acts at the center of mass, which is located at the geometrical center of the refrigerator.
The torque produced by the gravitational force is given by:
[tex]τ_{gravity} = F_{gravity} * d[/tex]
where F_gravity is the gravitational force, and d is the perpendicular distance from the line of action of the force to the pivot point (in this case, the edge of the refrigerator that is in contact with the floor). Since the refrigerator is symmetric, the center of mass is at the midpoint of the height, which is 1.0 m above the floor. Therefore:
[tex]F_{gravity} = m g = 120 kg x 9.81 m/s^2 = 1177.2 N[/tex]
d = 1.0 m
[tex]τ_{gravity} = 1177.2 N *1.0 m = 1177.2 Nm[/tex]
Next, we need to calculate the torque produced by the force of friction when the refrigerator is about to tip over.
The force of friction acts at the point of contact between the refrigerator and the floor, which is at the bottom of the refrigerator. The torque produced by the force of friction is given by:
[tex]τ_{friction} = F_{friction} h[/tex]
where F_friction is the force of friction, and h is the perpendicular distance from the line of action of the force to the pivot point (in this case, the same edge of the refrigerator that is in contact with the floor). Since the coefficient of static friction is 0.30, the maximum force of friction that can be exerted on the refrigerator without it tipping over is:
[tex]F_{friction} = μ_{s} F_{gravity} = 0.30* 1177.2 N = 353.16 N[/tex]
To determine the maximum height at which you can push the refrigerator without it tipping over, we need to find the value of h that makes τ_gravity = τ_friction. Therefore:
1177.2 Nm = 353.16 N x h
h = 1177.2 Nm / 353.16 N = 3.33 m
To know more about gravitational force refer here
https://brainly.com/question/12528243#
#SPJ11
Which statements describe a closed circuit? select three options. bulbs will shine. bulbs will not shine. the circuit is incomplete. the circuit is complete. charges flow. charges do not flow.
The statements describe a closed circuit: bulbs will shine, the circuit is complete, the circuit is complete.
A closed circuit can be described by the following three statements:
1. Bulbs will shine: In a closed circuit, the electrical components such as bulbs are connected in a complete loop, which allows the current to flow through them, causing the bulbs to shine.
2. The circuit is complete: A closed circuit has a continuous path for the charges to flow through. This means there are no breaks or gaps in the connections, allowing the current to move without interruption.
3. Charges flow: Since a closed circuit is complete, it enables the flow of electrical charges (or current) through the circuit. This continuous flow of charges is what powers the devices connected to the circuit.
In summary, a closed circuit is characterized by bulbs shining, a complete circuit, and the flow of charges. This is in contrast to an open circuit, where the circuit is incomplete, and charges do not flow, resulting in bulbs not shining.
To know more about circuit, refer here:
https://brainly.com/question/29765546#
#SPJ11
Complete question:
Which statements describe a closed circuit? select three options.
bulbs will shine.
bulbs will not shine.
he circuit is incomplete.
the circuit is complete.
charges flow.
charges do not flow.
ightning is an electrostatic discharge between two electrically charged regions that allows electrons in a negatively charged region to flow back to the positive region. how did these regions in thunderstorms get oppositely charged to begin with?
The process of charge separation, driven by updrafts and downdrafts in a thunderstorm, causes regions within the storm cloud to become oppositely charged, leading to the Electrostatic discharge known as lightning.
Lightning occurs due to electrostatic discharge between two electrically charged regions within a thunderstorm. These regions become oppositely charged through a process called charge separation.
Charge separation begins when updrafts and downdrafts within a thunderstorm cause ice particles, hail, and water droplets to collide. During these collisions, electrons are transferred between particles, resulting in some particles becoming positively charged while others become negatively charged.
The lighter, positively charged ice particles are carried upward by the updrafts, accumulating at the top of the storm cloud. Conversely, the heavier, negatively charged particles, such as hail, are carried downward by gravity and downdrafts, accumulating at the base of the cloud.
This separation of charges creates an electric field between the top and bottom regions of the cloud. When the electric field becomes strong enough, it overcomes the air's insulating properties, allowing electrons to flow from the negatively charged region to the positively charged region. This flow of electrons results in a lightning discharge.
In summary, the process of charge separation, driven by updrafts and downdrafts in a thunderstorm, causes regions within the storm cloud to become oppositely charged, leading to the electrostatic discharge known as lightning.
To Learn More About Electrostatic
https://brainly.com/question/17692887
SPJ11
In a recent movie, a car and a truck had a head on collision. The car was moving to the right with a constant speed of 21 m/s. A parked truck that was 310 m in front of the car began moving to the left and speeding up at a rate of 1.2 m/s/s. Position 0 m is the car's initial position.
What is the position of the car after 4 seconds?
What is the position of the truck after 4 seconds?
What is the velocity of the truck upon impact with the car?
How much time passes before the collision happens?
Where do the car and truck collide?
Answer:To solve this problem, we need to use the equations of motion and kinematics.
1. What is the position of the car after 4 seconds?
The position of the car after 4 seconds can be found using the equation:
position = initial position + (initial velocity x time) + (1/2 x acceleration x time^2)
Plugging in the values, we get:
position = 0 + (21 x 4) + (1/2 x 0 x 4^2) = 84 meters
Therefore, the position of the car after 4 seconds is 84 meters.
2. What is the position of the truck after 4 seconds?
The position of the truck after 4 seconds can be found using the equation of motion for uniform acceleration:
position = initial position + (initial velocity x time) + (1/2 x acceleration x time^2)
Initial velocity of the truck is zero, and the acceleration is 1.2 m/s^2. The initial position of the truck is 310 meters ahead of the car.
Plugging in the values, we get:
position = 310 + (0 x 4) + (1/2 x 1.2 x 4^2) = 326.4 meters
Therefore, the position of the truck after 4 seconds is 326.4 meters.
3. What is the velocity of the truck upon impact with the car?
To find the velocity of the truck upon impact with the car, we need to use the equation:
final velocity = initial velocity + acceleration x time
The initial velocity of the truck is zero, the acceleration is 1.2 m/s^2, and the time is the time it takes for the collision to happen.
4. How much time passes before the collision happens?
To find the time it takes for the collision to happen, we need to use the equations of motion and kinematics.
The position of the car at the time of the collision is the same as the position of the truck at the time of the collision. Let's call this position "x".
Using the equation of motion for the car, we have:
x = 0 + (21 x t) + (1/2 x 0 x t^2) = 21t
Using the equation of motion for the truck, we have:
x = 310 + (0 x t) + (1/2 x 1.2 x t^2) = 0.6t^2 + 310
Setting these two equations equal to each other, we get:
21t = 0.6t^2 + 310
Simplifying and solving for t, we get:
t = 23.98 seconds
Therefore, the time it takes for the collision to happen is approximately 24 seconds.
5. Where do the car and truck collide?
The position of the collision can be found by plugging the time into either the equation of motion for the car or the equation of motion for the truck.
Using the equation of motion for the car:
position = 21 x 23.98 = 503.58 meters
Using the equation of motion for the truck:
position = 0.6 x (23.98)^2 + 310 = 503.58 meters
Therefore, the car and truck collide at a position of 503.58 meters.
Explanation:
State 2 advantages of alkaline accumulators over lead-acid accumulators
Two advantages of alkaline accumulators over lead-acid accumulators are:
1. Higher energy density: Alkaline accumulators have a higher energy density than lead-acid accumulators, which means they can store more energy in the same volume or weight of battery. This makes them ideal for portable devices where size and weight are important factors.
2. Longer cycle life: Alkaline accumulators have a longer cycle life than lead-acid accumulators, which means they can be charged and discharged many more times before they need to be replaced.
This makes them a more cost-effective and reliable option for applications where the battery will be used frequently, such as in electric vehicles or renewable energy systems.
To know more about Alkaline accumulators refer here
https://brainly.com/question/24287288#
#SPJ11
Determine the forces in all the members and state if these members are in tension or compression,use table to arrange your calculations (show the results on the truss)
To determine the forces in all the members, we have to consider as follows:
1. Draw the truss and label all the members and joints.
2. Determine the support reactions by solving the equilibrium equations (sum of vertical forces, horizontal forces, and moments should be zero).
3. Using the Method of Joints or Method of Sections, analyze each joint or section by applying the equilibrium equations.
4. For each member, calculate the force and determine if it is in tension or compression based on the direction of the force acting on the member.
5. Organize your results in a table with columns for the member label, force value, and whether the force is tension or compression.
6. Finally, show the results on the truss by indicating the force magnitudes and whether each member is in tension or compression.
Remember that for a more accurate answer, I need more details about the truss you are analyzing.
To learn more about compression, refer below:
https://brainly.com/question/30060592
#SPJ11
A 0. 068-kg ball strikes a wall with a velocity of 22. 1 m/s. The wall stops the ball in 0. 63 s. What is the magnitude of the
force applied by the wall on the ball?
a. 5. 3n
b. 4. 2n
c. 12n
d. 2. 4n
The correct answer is (d) 2.4 N. We can use the impulse-momentum theorem to solve this problem. The impulse of the force is equal to the change in momentum of the ball.
The initial momentum of the ball is: p1 = mv = (0.068 kg)(22.1 m/s) = 1.5038 kg*m/s
Since the wall stops the ball, the final momentum of the ball is zero: p2 = 0 kg*m/s
The change in momentum is: Δp = p2 - p1 = -1.5038 kg*m/s
The time interval for the force to act is 0.63 s.
So, the magnitude of the force applied by the wall on the ball is: F = Δp / Δt = (-1.5038 kg*m/s) / (0.63 s) ≈ 2.4 N
Therefore, the correct answer is (d) 2.4 N.
To know more about impulse-momentum, refer here:
https://brainly.com/question/904448#
#SPJ11
The force responsible for normal expiration is supplied by the:.
The force responsible for normal expiration is supplied by the elastic recoil of the lungs and chest wall. During inhalation, the diaphragm and intercostal muscles contract, causing the chest cavity to expand and the lungs to fill with air.
When the muscles relax, the chest cavity and lungs recoil back to their resting positions, expelling air out of the lungs. The elastic recoil of the lungs and chest wall generates the force needed for normal expiration.
To know more about elastic recoil refer here
https://brainly.com/question/9491266#
#SPJ11
A plane monochromatic electromagnetic wave with wavelength λ=2. 0cm, propagates through a vacuum. Its magnetic field is described by >B⃗ =(Bxi^+Byj^)cos(kz+ωt), where Bx=1. 9×10−6T,By=4. 7×10−6T, and i^ and j^ are the unit vectors in the +x and +y directions, respectively. What is Sz, the z-component of the Poynting vector at (x=0,y=0,z=0) at t=0?
The z-component of the Poynting vector of plane monochromatic electromagnetic wave with wavelength λ=2. 0cm at (x=0,y=0,z=0) at t=0 is -2.44×10⁻¹¹W/m².
Poynting vector describes the flow of energy in an monochromatic electromagnetic wave and is given by:
>S⃗=1/μ0(E⃗ ×B⃗ )
where μ0 is the permeability of free space, E⃗ is the electric field vector, and B⃗ is the magnetic field vector. In this case, we are given the magnetic field vector as:
>B⃗ =(Bxi^+Byj^)cos(kz+ωt)
To find the z-component of the Poynting vector at (x=0,y=0,z=0) at t=0, we first need to determine the electric field vector. We know that the wave is monochromatic, meaning it has a single frequency, and we are given the wavelength λ=2.0cm. We can use the relationship between wavelength and frequency:
>c=λf
where c is the speed of light, to find the frequency:
>f=c/λ
>f=(3.00×10⁸ m/s)/(0.02 m)
>f=1.50×10¹⁰ Hz
Now we can use the relationship between the electric and magnetic fields in an electromagnetic wave:
>E=cB
to find the electric field vector:
>E=c(Bxi^+Byj^)
>E=(3.00×10⁸ m/s)(1.9×10⁻⁶ xi^+4.7×10⁻⁶ yj^)
>E=(5.70×10² V/m)xi^+(1.41×10³ V/m)yj^
We can now substitute the magnetic and electric field vectors into the expression for the Poynting vector:
>S⃗=1/μ0(E⃗ ×B⃗ )
>S⃗=1/μ0[(5.70×10²2 xi^+1.41×10³ yj^)×(1.9×10−6 xi^+4.7×10⁻⁶ yj^)]cos(kz+ωt)
>S⃗=1/μ0(−8.91×10⁻¹⁶z^)cos(kz+ωt)
where z^ is the unit vector in the +z direction. Plugging in the values for μ0, k, and ω, we get:
>S⃗=−2.44×10−11z^W/m²
where W/m² represents the units of power per unit area. Finally, we need to find the z-component of the Poynting vector at (x=0,y=0,z=0) at t=0, so we plug in those values:
>Sz=−2.44×10−11(1) W/m²
>Sz=−2.44×10−11 W/m²
Therefore, the z-component of the Poynting vector at (x=0,y=0,z=0) at t=0 is -2.44×10^-11 W/m².
Learn more about monochromatic electromagnetic wave at: https://brainly.com/question/14477656
#SPJ11
Brainliest if correct!_A particle is projected vertically upwards from a fixed point O. The speed of projection is u m/s. The particle returns to O 4 seconds later. Find:
a) the value of u
b) the greatest height reached by the particle
c) the total time of which the particle is at a height greater than half its greatest height
Thank you so much!
The velocity, u, has a value of 19.6 m/s. The particle has a maximum height of 19.6 m. The particle spends a total of 2.33 s at a height more than half of its highest height.
What does the velocity, u, equal?We can apply the formula for the period of flight of a vertically projected particle to determine the value of the velocity, u: t = 2u/g.
After 4 seconds, the particle returns to the same location, therefore we have:
2t = 4
When the value of t is substituted in the first equation, we obtain:
u = gt/2 = 9.8 x 2
u = 19.6 m/s
b) The formula for the maximum height attained by a vertically projected particle can be used to determine the particle's greatest height:
h = u²/2g
Substituting the value of u, we get:
h = 19.6²/(2 x 9.8)
h = 19.6 m
b) We can first determine the height at which the particle is half its greatest height in order to determine the total amount of time the particle is at a height higher than half its greatest height:
[tex]h/2 = (u^2/2g)/2 = u^2/4g[/tex]
Substituting the value of u, we get:
[tex]h/2 = 19.6^2/(4 x 9.8) = 24.01 m[/tex]
Therefore, when the particle is over 24.01 m, it is at a height that is larger than half of its maximum height.
Next, we can determine how long it took the particle to ascend to this height:
[tex]h = ut - (1/2)gt^224.01 = 19.6t - (1/2)9.8t^2[/tex]
Solving this quadratic equation, we get:
t =2.33s or t=4.10 s
The particle ascends to a height of 24.01 m in 2.33 seconds, and it descends to the ground in 1.67 seconds (4 - 2.33).
To know more about velocity visit:-
https://brainly.com/question/17127206
#SPJ1
An engine is received that hunts and surges at top no-load speed only. to determine whether the carburetor or the governor system is causing the symptom, a specific troubleshooting process can be followed. technician a says that to separate the governor system from the carburetor, simply hold the throttle plate still and see if the engine continues to hunt & surge. technician b says that hunting and surging is caused exclusively by a lean mixture in the carburetor. which technician is correct? technician a technician b both technicians a and b neither technicians a nor b
Technician A is correct in their suggestion to separate the governor system from the carburetor by holding the throttle plate still, while Technician B is incorrect in stating that hunting and surging is caused exclusively by a lean mixture in the carburetor. Therefore, the correct answer is Technician A.
Technician A is correct. To determine whether the carburetor or the governor system is causing the hunting and surging symptom at top no-load speed, holding the throttle plate still is a useful troubleshooting process. By holding the throttle plate still, the engine can be tested to see if it continues to hunt and surge, which will help determine if the governor system or the carburetor is causing the issue. This method allows for the separation of the governor system from the carburetor, making it easier to identify the cause of the problem.
On the other hand, Technician B is not entirely correct. While a lean mixture in the carburetor can cause hunting and surging, it is not the only possible cause. Other factors such as a malfunctioning governor system can also result in these symptoms. Therefore, it is essential to follow the troubleshooting process outlined by Technician A to accurately identify the cause of the problem and address it effectively.
For more about governor system:
https://brainly.com/question/15993503
#SPJ11
A toaster is listed as 1560 w. when it is plugged into a 120 v circuit and starts to make toast, how many amperes will it draw
The toaster will draw 13.0 amperes when plugged into a 120-volt circuit.
To calculate the amperage that the toaster will draw, we can use Ohm's Law which states that the current flowing through a circuit is equal to the voltage divided by the resistance.
However, we need to first determine the resistance of the toaster.
From the given information, we know that the toaster is rated at 1560 watts and is operating at 120 volts.
Therefore, we can calculate the resistance using the formula R = [tex]V^{2}[/tex] / P, where V is the voltage and P is the power.
R = [tex](120)^{2}[/tex] / 1560 = 9.23 ohms
Now that we know the resistance, we can use Ohm's Law to calculate the current drawn by the toaster:
I = V / R = 120 / 9.23 = 13.0 A
Therefore, the toaster will draw 13.0 amperes when plugged into a 120-volt circuit.
To know more about Ohm's Law, refer here:
https://brainly.com/question/1247379#
#SPJ11
(b) The aluminium wire will break if the tension in the wire exceeds 350N.
The wire is attached to the flagpole at B, 0. 8 m from the wall.
The wire is at an angle of 20° to the flagpole.
Assess whether the wire will break. You should use the principle of moments, taking
moments about 0.
length of flagpole = 1. 2m
mass of flagpole and flag = 15 kg
The wire won't break because the tension is less than 350N. To assess whether the wire will break, we need to calculate the tension in the wire using the principle of moments to do this, taking moments about point 0.
First, we need to calculate the weight of the flagpole and flag. We know that mass = 15 kg, so we can use the formula weight = mass x gravity, where gravity = 9.8 m/s^2. Therefore, weight = 15 x 9.8 = 147 N.
Next, we need to calculate the force exerted by the wire. We can use trigonometry to find the horizontal and vertical components of this force. The horizontal component is given by F_h = F x cos θ, where F is the tension in the wire and θ is the angle between the wire and the flagpole. In this case, F_h = F x cos 20°.
The vertical component is given by F_v = F x sin θ. In this case, F_v = F x sin 20°.
Now, we can take moments about point 0. The weight of the flagpole and flag acts vertically downwards at a distance of 0.8 m from point 0, so its moment is 147 x 0.8 = 117.6 Nm (clockwise).
The force exerted by the wire acts at an angle of 20° to the flagpole, so its horizontal component acts perpendicular to the flagpole and its vertical component acts parallel to the flagpole. The horizontal component has no moment about point 0, so we only need to consider the vertical component. This acts at a distance of 1.2 m from point 0, so its moment is F_v x 1.2 (anticlockwise).
Setting the moments equal to each other, we get:
147 x 0.8 = F_v x 1.2 x sin 20°
Simplifying this equation, we get:
F_v = 78.7 N
To find the tension in the wire, we can use Pythagoras' theorem:
F = √(F_h^2 + F_v^2) = √((F x cos 20°)^2 + 78.7^2)
Simplifying this equation, we get:
F = 87.6 N
Since the tension in the wire is less than 350N, the wire will not break.
Know more about Tension here:
https://brainly.com/question/30470948
#SPJ11
What is (fnet3)x , the x-component of the net force exerted by these two charges on a third charge q3 = 48.0 nc placed between q1 and q2 at x3 = -1.145 m ? your answer may be positive or negative, depending on the direction of the force.
The x-component of the net force exerted by [tex]q_1[/tex] and [tex]q_2[/tex] on [tex]q_3[/tex] is -5.33 x [tex]10^{-3}[/tex] N, indicating that [tex]q_3[/tex] is attracted towards [tex]q_1[/tex].
What is Charge?
Charge is a fundamental property of matter that describes the amount of electrical energy that a particle possesses. It is a physical property that can be either positive or negative and is measured in units of coulombs (C).
To calculate the x-component of the net force, we need to consider the x-components of the distances and forces. Since [tex]q_3[/tex] is placed between [tex]q_1[/tex]and [tex]q_2[/tex], we can calculate the distances as follows:
[tex]r_1[/tex] = [tex]x_3[/tex] - [tex]x_1[/tex] = (-1.145 m) - (0 m) = -1.145 m
[tex]r_2[/tex] = [tex]x_2[/tex] - [tex]x_3[/tex] = (0.855 m) - (-1.145 m) = 2 m
Note that we use the signs of the distances to indicate the directions of the forces.
The x-components of the forces can be calculated using trigonometry:
F[tex]x_1[/tex] = F1 * cos(theta1) = k * [tex]q_1[/tex] * [tex]q_3[/tex] / [tex]r_1[/tex] * cos(theta1)
F[tex]x_2[/tex] = F2 * cos(theta2) = k * [tex]q_2[/tex] * [tex]q_3[/tex] / [tex]r_2[/tex] * cos(theta2)
where theta1 and theta2 are the angles between the forces and the x-axis.
Since [tex]q_1[/tex] and [tex]q_2[/tex] are both positive, they repel each other and the force on [tex]q_3[/tex] is negative, indicating that it is attracted towards the negative side of the x-axis, which is towards [tex]q_1[/tex].
Using trigonometry, we can calculate the angles as follows:
theta1 = arctan(y1 / [tex]x_1[/tex]) = arctan(0 / (-1.145 m)) = 0 rad
theta2 = arctan(y2 / [tex]x_2[/tex]) = arctan(0 / (0.855 m)) = 0 rad
Therefore, the x-components of the forces are:
F[tex]x_1[/tex] = k *[tex]q_1[/tex] *[tex]q_3[/tex] / [tex]r_1[/tex]^2 * cos(0 rad) = -3.31 x [tex]10^{-3}[/tex] N
F[tex]x_2[/tex] = k * [tex]q_2[/tex] *[tex]q_3[/tex] / [tex]r_2[/tex]^2 * cos(0 rad) = -2.02 x [tex]10^{-3}[/tex] N
The net force on [tex]q_3[/tex] is the sum of the forces:
Fnetx = F[tex]x_1[/tex] + F[tex]x_2[/tex] = -5.33 x [tex]10^{-3}[/tex] N
To know more about Charge visit;
https://brainly.com/question/18102056
#SPJ4
A spaceship has four thrusters for movement. Each thruster can fire exhaust gases away from the ship, causing it to move. Firing which pairs of thrusters together would cause the ship to remain stationary?
Thrusters 1 and 2
, Thrusters 1 and 2 , ,
Thrusters 1 and 3
, Thrusters 1 and 3 , ,
Thrusters 3 and 4
, Thrusters 3 and 4 , ,
Thrusters 2 and 3
, Thrusters 2 and 3 , ,
Thrusters 1 and 4
, Thrusters 1 and 4 , ,
Thrusters 2 and 4
The two pairs of thrusters that would cause the spaceship to remain stationary when fired together are: Thrusters 1 and 2, and Thrusters 3 and 4.
Thrust is the force that propels an object forward, and it is created by the expulsion of gas or liquid out of a nozzle. In the case of a spaceship, the thrusters create thrust by expelling exhaust gases away from the ship, which propels it forward.
Now, let's consider the thrusters on this spaceship. There are four thrusters available for movement, which means that there are six possible pairs of thrusters that can be fired together. However, not all of these pairs will result in the ship remaining stationary.
To keep the spaceship stationary, the thrusters need to create an equal and opposite force to cancel out the movement created by the other thrusters. This means that the pairs of thrusters that need to be fired together are those that are opposite each other.
we need to consider the opposite forces acting on the ship. If two thrusters generate equal and opposite forces, the net force will be zero, and the spaceship will remain stationary.
Assuming the thrusters are arranged symmetrically around the spaceship, firing Thrusters 1 and 2 together or Thrusters 3 and 4 together would likely create equal and opposite forces. This is because the forces generated by these pairs would cancel each other out, keeping the ship stationary.
Therefore, the two pairs of thrusters that would cause the spaceship to remain stationary when fired together are Thrusters 1 and 2, and Thrusters 3 and 4.
To know more about thrusters, refer here:
https://brainly.com/question/30154005#
#SPJ11
Complete question:
A spaceship has four thrusters for movement. Each thruster can fire exhaust gases away from the ship, causing it to move. Firing which pairs of thrusters together would cause the ship to remain stationary?
Select two that apply
Thrusters 3 and 4
Thrusters 1 and 2
Thrusters 1 and 3
Thrusters 2 and 4
Thrusters 2 and 3
Thrusters 1 and 4
A kettle is made from metal. If the live wire inside this kettle were to come loose and touch the metal casing, you could get an __________ __________ if you then touched the kettle. What two words complete this sentence?
Answer: electric shock
Explanation: cuz metal is conductor of electricity
The basics of _________ fusion in the Sun are detailed in the following important summary (i. E. , understand this material). Normally, protons repel each other because their charges are similar, and by analogy consider trying bring together the N of a magnet with the N of another magnet. To overcome that electromagnetic repulsion one needs to smash the protons at a very high speed, and then nuclear fusion can occur. That high speed is not achieved in daily life, thankfully, but in the cores of stars where the temperature is high. Temperature is a proxy for the speed of particles, and as an example consider if it is cold in the room the particles are moving slowly. The temperature is high in the cores of stars because there is the sizable mass of all the overlaying layers exerting a pressure on the core, and causing the temperature to rise, and hence the speed of the protons. By analogy, consider when diving from the top of the pool to the bottom of the pool, and where one begins to feel the pressure exerted by all the overlaying layers of water
Answer:
The basics of proton-proton fusion in the Sun are detailed in the following important summary:
Normally, protons repel each other because their charges are similar. This is similar to trying to bring together the north pole of a magnet with the north pole of another magnet.
To overcome that electromagnetic repulsion, one needs to smash the protons at a very high speed. This is similar to how two magnets can be brought together if they are moving very fast.
That high speed is not achieved in daily life, thankfully, but in the cores of stars where the temperature is high.
Temperature is a proxy for the speed of particles. For example, if it is cold in a room, the particles are moving slowly.
The temperature is high in the cores of stars because there is the sizable mass of all the overlaying layers exerting a pressure on the core. This pressure causes the temperature to rise, and hence the speed of the protons.
By analogy, consider when diving from the top of the pool to the bottom of the pool. As you descend, you begin to feel the pressure exerted by all the overlaying layers of water.
In the core of the Sun, the temperature is about 15 million degrees Celsius. This is hot enough for the protons to move at very high speeds. When two protons collide at high speed, they can fuse together to form a helium nucleus. This process releases a large amount of energy, which is what powers the Sun.
The proton-proton fusion reaction is a complex process, but it is essential for the Sun to shine. Without this reaction, the Sun would eventually cool and collapse.
A centrifuge has a diameter of 18cm. It is able to spin at 10,000 rpm.
A. What is the centripetal acceleration of the centrifuge?
B. If we place a 10 9 gram sample into the centrifuge, what is the force on the sample?
C. How many times greater than the force of gravity is this force?
About 10,080 times more force than gravity is exerted on the sample in the centrifuge.
A. To calculate the centripetal acceleration of the centrifuge, you can use the formula:
a_c = rω²
where a_c is centripetal acceleration, r is the radius of the centrifuge, and ω is angular velocity. First, we need to convert the diameter to the radius (r = 0.09 m) and RPM to radians per second (ω = 10,000 RPM * 2π / 60 ≈ 1047.2 rad/s).
a_c = 0.09 m * (1047.2 rad/s)² ≈ 98,960 m/s²
B. To find the force on the 10-gram sample, we can use the formula:
F = m * a_c
where F is force, m is the mass of the sample (0.01 kg), and a_c is the centripetal acceleration from part A.
F = 0.01 kg * 98,960 m/s² ≈ 989.6 N
C. To determine how many times greater than the force of gravity this force is, we can divide the force by the gravitational force on the sample:
F_gravity = m * g
F_gravity = 0.01 kg * 9.81 m/s² ≈ 0.0981 N
Force ratio = F / F_gravity ≈ 989.6 N / 0.0981 N ≈ 10,080
So, the force on the sample in the centrifuge is approximately 10,080 times greater than the force of gravity.
Know more about centripetal acceleration here:
https://brainly.com/question/14465119
#SPJ11
A man pulled a food cart 4. 5 m to the right for 15 seconds. What is the average speed of the food cart to the nearest tenth of a m/s
A man pulled a food cart 4. 5 m to the right for 15 seconds. The average speed of the food cart to the nearest tenth is 0.3 m/s. The average speed of the food cart can be calculated by dividing the total distance traveled by the time taken.
In this case, the distance traveled is 4.5 m, and the time taken is 15 seconds. Thus, the average speed of the food cart can be calculated as:
average speed = total distance / time taken = 4.5 m / 15 s = 0.3 m/s
Therefore, the average speed of the food cart is 0.3 m/s.
To understand this calculation, it is important to know the definition of speed, which is the distance traveled per unit of time. In this case, the distance traveled is the horizontal distance the food cart was pulled, and the time taken is the duration of the pulling.
The average speed is the total distance traveled divided by the time taken. This calculation assumes that the speed is constant over the duration of the motion.
In summary, the average speed of the food cart is 0.3 m/s, calculated by dividing the total distance traveled (4.5 m) by the time taken (15 s).
To know more about speed refer here:
https://brainly.com/question/28060745#
#SPJ11
Terry is out with friends and sees a man who appears to be struggling with mental illness. He is ranting and waving his arms around in a very antagonistic way. He is getting more agitated and pulls out a knife and starts jabbing it like he is attacking someone. Should Terry call 9-1-1?
Yes, Terry should call 9-1-1 immediately because the man is mentally ill.
What should Terry do?Based on the statement, if Terry is out with friends and sees a man who appears to be struggling with mental illness. And the man is ranting and waving his arms around in a very antagonistic way. He is also getting more agitated and pulls out a knife and starts jabbing it like he is attacking someone.
The man's behavior is dangerous and poses a potential threat to himself and others around him. The fact that he has pulled out a knife and is waving it in a threatening manner indicates that he may be a danger to himself or others.
In this situation, it is important to prioritize everyone's safety and call for emergency services to intervene and help the man.
Learn more about emergency situations here: https://brainly.com/question/28335200
#SPJ1
A. 149 kg baseball moving at 17. 7 m/s is caught by a 57 kg catcher at rest on an ice skating rink, wearing
frictionless skates. With what speed does the catcher slide on the ice?
Do NOT put in units or it will be marked wrong! The answer's value only! Please round each answer to 3 places.
MaVa + MbVb = (Ma+b)(Va+b)
The speed at which the catcher slides on the ice after catching the 149 kg baseball moving at 17.7 m/s is 12.80 m/s. it can be found using the conservation of momentum formula: MaVa + MbVb = (Ma + Mb)(Va+b).
In this case, Ma represents the mass of the baseball (149 kg)
Va represents the initial velocity of the baseball (17.7 m/s)
Mb represents the mass of the catcher (57 kg), and Vb represents the initial velocity of the catcher (0 m/s, as he is at rest).
We need to solve for Va+b, which represents the final velocity of the catcher after catching the baseball.
Plugging in the given values, we have:
(149 kg)(17.7 m/s) + (57 kg)(0 m/s) = (149 kg + 57 kg)(Va+b)
2637.3 kg·m/s = (206 kg)(Va+b)
To find the final velocity of the catcher (Va+b), we can now divide both sides by the total mass (206 kg):
Va+b = 2637.3 kg·m/s / 206 kg = 12.80 m/s
Therefore, the catcher slides on the ice with a speed of approximately 12.80 m/s after catching the baseball. Please remember to round your answer to 3 decimal places as required.
Know more about conservation of momentum click here:
https://brainly.com/question/24989124
#SPJ11
Is it possible to play the lowest string with your finger on any of the frets shown and hear the same frequency as the highest string?.
No, it is not possible to play the lowest string with your finger on any of the frets shown and hear the same frequency as the highest string.
The frets on a stringed instrument, such as a guitar, are placed in specific positions along the neck to produce different pitches or frequencies when the strings are pressed against them.
Each fret represents a specific note, and when you press a string against a particular fret, you effectively shorten the vibrating length of the string, which increases the frequency and raises the pitch of the sound produced.
As you move your finger along the fretboard, the pitch of the note played changes.
The lowest string on a guitar, typically the thickest string, has the lowest pitch or frequency when played open (without pressing any frets). As you press down on higher frets, you increase the pitch of the note.
The highest string on a guitar, typically the thinnest string, has the highest pitch or frequency when played open.
Therefore, pressing a fret on the lowest string will never produce the same frequency as the open (unfretted) highest string because the length and tension of the strings are different, resulting in different natural frequencies for each string.
To know more about string refer here
https://brainly.com/question/946868#
#SPJ11
The length of speed's hand of watch is 1cm the change in velocity of is tip in 15 sec
The change in velocity of the tip of the second's hand in 15 seconds is: [tex]\pi /(30\sqrt2) cm/s[/tex]. The correct option is B.
To determine the change in velocity of the tip of the second's hand, we need to consider that the hand moves in a circular path with a radius of 1 cm. In 15 seconds, the angle covered is (15/60) × 360 = 90 degrees, or π/2 radians.
The initial velocity can be represented as (v1 = rω1) and the final velocity as (v2 = rω2), where r is the radius (1 cm) and ω is the angular velocity. Since the second's hand moves at a constant speed, the angular velocities are equal, and the change in velocity (∆v) can be calculated using the formula:
∆v = √(v1² + v2² - 2*v1*v2cos(π/2))
Since cos(π/2) = 0, the formula simplifies to:
∆v = √(v1² + v2²)
As v1 = v2 = rω,
∆v = √(2(rω)²) = rω√2 = (1cm)(π/30 rad/s)√2 = π/(30√2) cm/s
So, the change in velocity of the tip of the second's hand in 15 seconds is π/(30√2) cm/s. The correct option is B.
To know more about velocity , refer here:
https://brainly.com/question/1482529#
#SPJ11
Complete question:
The length of speed's hand of watch is 1cm the change in velocity of is tip in 15 sec
A. zero
B. π/(30√2)
C. π/30
D. 2π/(30√2)
1. Using a block-and-tackle, a mechanic pulls 8. 2 m of chain with a force of 90 N in
order to lift a 320 N motor to a height of 2. 9 m.
a) What is the AMA( Actual mechanical advantage) 10 points
b) What is the IMA (Ideal Mechanical Advantage) 10 points
c. What is the efficiency of the block-and-tackle? (10 points)
a) To calculate the actual mechanical advantage (AMA), we use the formula:
AMA = Output Force / Input Force
In this case, the output force is the weight of the motor being lifted, which is 320 N. The input force is the force applied by the mechanic, which is 90 N.
AMA = 320 N / 90 N
AMA ≈ 3.56 (rounded to two decimal places)
Therefore, the actual mechanical advantage (AMA) is approximately 3.56.
b) The ideal mechanical advantage (IMA) of a block-and-tackle system is determined by the number of supporting ropes or chains. Since the problem does not mention the specific arrangement of the block-and-tackle system, we cannot calculate the exact IMA. However, in a simple block-and-tackle system, the IMA is equal to the number of rope segments supporting the load. If we assume a simple one-rope segment system, then the IMA would be 1.
c) Efficiency is defined as the ratio of output work to input work, expressed as a percentage. The formula for efficiency is:
Efficiency = (Output Work / Input Work) x 100
Output work is calculated as the product of the output force and the distance lifted. In this case, it is 320 N multiplied by 2.9 m. Input work is calculated as the product of the input force and the distance moved. Here, it is 90 N multiplied by 8.2 m.
Output Work = 320 N * 2.9 m = 928 N·m
Input Work = 90 N * 8.2 m = 738 N·m
Efficiency = (928 N·m / 738 N·m) x 100
Efficiency ≈ 125.88% (rounded to two decimal places)
Note: The efficiency value obtained here is higher than 100%, which is not physically possible. It is likely due to rounding errors or approximations made during the calculations. In practical scenarios, efficiencies are always less than 100%.
To know more about block-and-tackle system refer here
https://brainly.com/question/3415871#
#SPJ11
Suppose you can jump 1 m on earth. how high would you be able to jump on
mars? the mass of mars is 6.4181023kg and its radius is 3.38106m.
To determine how high you would be able to jump on Mars compared to Earth, we can use the concept of gravitational potential energy.
On both Earth and Mars, the gravitational potential energy (PE) is given by the equation:
PE = mgh
where m is your mass, g is the acceleration due to gravity, and h is the height.
The acceleration due to gravity can be calculated using Newton's law of universal gravitation:
g = (G * M) / (r^2)
where G is the gravitational constant, M is the mass of the celestial body (in this case, Mars), and r is the distance from the center of the celestial body to the surface (in this case, the radius of Mars).
Let's assume your mass is the same on both Earth and Mars.
On Earth, the acceleration due to gravity (g_Earth) is approximately 9.8 m/s^2, and the height (h_Earth) is 1 m.
PE_Earth = m * g_Earth * h_Earth
On Mars, we need to calculate the acceleration due to gravity (g_Mars) using the given mass and radius of Mars. The gravitational constant (G) is approximately 6.67430 × 10^(-11) m^3/(kg s^2).
g_Mars = (G * M) / (r^2)
g_Mars = (6.67430 × 10^(-11) m^3/(kg s^2) * 6.418 * 10^(23) kg) / (3.38106 m)^2
Now we can calculate the height (h_Mars) you would be able to jump on Mars:
PE_Mars = m * g_Mars * h_Mars
Since we are assuming the same mass on both Earth and Mars, we can set the potential energies on Earth and Mars equal to each other and solve for h_Mars:
m * g_Earth * h_Earth = m * g_Mars * h_Mars
h_Mars = (g_Earth / g_Mars) * h_Earth
Now we can substitute the values and calculate the height you would be able to jump on Mars:
h_Mars = (9.8 m/s^2 / g_Mars) * 1 m
To know more about potential energy refer here
https://brainly.com/question/14294569#
#SPJ11
achievement and challenges of science and technology explain?
Science and technology have had a significant influence on society, with both successes and difficulties.
The achievements can be noted as -
Medical Growth - Scientists and medical professionals have been able to create vaccinations, medicines, and surgical techniques thanks to advancements in technology that save millions of lives annually. This covers developments like cancer therapy, organ transplantation, and enhanced medical imaging. Communication Growth - People may now contact and communicate with one another more easily because to developments in communication technology. People may now communicate globally thanks to advancements in communication technologies, like the telephone and the internet.Commutation - Transport has also been enhanced by science and technology, becoming quicker and more effective. This includes technological advancements like electric autos, high-speed trains, and aeroplanes.The challenges can be noted as -
Environmental Degradation - Environmental degradation, including pollution, deforestation, and climate change, has been brought on by the development and usage of technology.Expensive - It may be expensive to develop and adopt new technology, which might put people and communities at a financial disadvantage. This may restrict access to these breakthroughs and worsen already existing inequities.Dependency - Genetic engineering, artificial intelligence, and privacy are just a few of ethical issues that have been brought up by these advancements. It is crucial to consider possible effects of these breakthroughs and make sure they are applied for the benefit of everybody.Read more about science and technology on:
https://brainly.com/question/28497175
#SPJ1
A small block sits at one end of a flat board that is 4.00 m
long. The coefficients of friction between the block and the board are μs
= 0.550 and μk
= 0.400. The end of the board where the block sits is slowly raised until the angle the board makes with the horizontal is α0
, and then the block starts to slide down the board.
The block will slide down the board with an acceleration of 0.426 m/s^2 when the board is at an angle of 30 degrees.
To solve this problem
We can solve this problem using the concepts of static and kinetic friction, and the relationship between force, mass, and acceleration.
The maximum angle α0 at which the block remains stationary is given by the equation:
tan(α0) = μs
Where μs is the coefficient of static friction.
We can solve for α0 as:
α0 = tan^-1(μs) = tan^-1(0.550) = 29.0 degrees
When the angle of the board is greater than α0, the block will begin to slide down the board. The force of friction acting on the block will change from static friction to kinetic friction. The force of friction is given by:
Ff = μk * Fn
Where
μk is the coefficient of kinetic friction Fn is the normal force acting on the blockThe normal force is equal to the weight of the block, which is given by:
Fn = mg
Where
m is the mass of the blockg is the acceleration due to gravity (9.81 m/s^2)We can now calculate the force of friction as:
Ff = μk * Fn = μk * mg
Once the block begins to slide down the board, the acceleration of the block is given by:
a = (sin(α) - μk*cos(α)) * g
Where α is the angle of the board with respect to the horizontal. We can solve for α by setting the force of friction equal to the component of the weight of the block acting parallel to the board:
Ff = m * g * sin(α) = m * a
Substituting Ff and solving for α, we get:
sin(α) = (μk*cos(α) + a/g)
Using the given values of μk and the length of the board, we can calculate the acceleration of the block for a given angle α. For example, if we set α = 30 degrees, we get
a = (sin(30) - μkcos(30)) * g = (0.5 - 0.4sqrt(3)/2) * 9.81 m/s^2 = 0.426 m/s^2
Therefore, the block will slide down the board with an acceleration of 0.426 m/s^2 when the board is at an angle of 30 degrees.
Learn more about kinetic friction here : brainly.com/question/20241845
#SPJ1
Please it due today need help!!!
Gender shifts are actually a common phenomenon in public roles (employment,
entertainment, or otherwise). Identify a role and explain if there is a status change
in the role - as in how these women or non binary folks are treated by the others
in the situation (still treated as women/non-binary or as if they are men-explain).
One example of a role where gender shifts occur is politics. Women and non-binary individuals who enter the political sphere often experience a shift in their status and how they are treated by others. They may be viewed as less competent or capable than their male counterparts, or face discrimination and bias based on their gender identity. However, as more women and non-binary individuals are elected to political positions, there is a growing recognition of their abilities and contributions, and a shift towards greater gender equality in the political realm. Despite this progress, there is still much work to be done to address the systemic barriers that prevent women and non-binary individuals from fully participating in politics and achieving equal status and treatment.
If a 325 W heater has a current of 6.0 A, what is the resistance of the heating element?
O 10 Ohms
O 50 Ohms
88 Ohms
9 Ohms
The resistance of the heating element is 9 Ohms
What is Ohm's law?Ohm's law states that the current (I) flowing through a conductor between two points is directly proportional to the voltage (V) across the two points and inversely proportional to the resistance (R) between them. Mathematically, this can be expressed as:
V = IR
Equation:In this scenario, we are given the power (P) and current (I) of a heater, and we are asked to find its resistance (R). Power can be calculated using:
P = IV
where V is the voltage across the heater. Since we are not given the voltage, we can rearrange Ohm's law to solve for the resistance:
R = V/I
Substituting the formula for power into this equation, we get:
R = (V/I) = (P/I²)
Substituting the given values of power and current, we get:
R = (325 W) / (6.0 A)² = 9.0 Ohms
The correct answer is (D).
To know more about Ohm's law, click here
https://brainly.com/question/1247379
#SPJ1