A centrifuge has a diameter of 18cm. It is able to spin at 10,000 rpm.


A. What is the centripetal acceleration of the centrifuge?


B. If we place a 10 9 gram sample into the centrifuge, what is the force on the sample?


C. How many times greater than the force of gravity is this force?

Answers

Answer 1

About 10,080 times more force than gravity is exerted on the sample in the centrifuge.

A. To calculate the centripetal acceleration of the centrifuge, you can use the formula:

a_c = rω²

where a_c is centripetal acceleration, r is the radius of the centrifuge, and ω is angular velocity. First, we need to convert the diameter to the radius (r = 0.09 m) and RPM to radians per second (ω = 10,000 RPM * 2π / 60 ≈ 1047.2 rad/s).

a_c = 0.09 m * (1047.2 rad/s)² ≈ 98,960 m/s²

B. To find the force on the 10-gram sample, we can use the formula:

F = m * a_c

where F is force, m is the mass of the sample (0.01 kg), and a_c is the centripetal acceleration from part A.

F = 0.01 kg * 98,960 m/s² ≈ 989.6 N

C. To determine how many times greater than the force of gravity this force is, we can divide the force by the gravitational force on the sample:

F_gravity = m * g
F_gravity = 0.01 kg * 9.81 m/s² ≈ 0.0981 N

Force ratio = F / F_gravity ≈ 989.6 N / 0.0981 N ≈ 10,080

So, the force on the sample in the centrifuge is approximately 10,080 times greater than the force of gravity.

Know more about centripetal acceleration here:

https://brainly.com/question/14465119

#SPJ11


Related Questions

imagine that you have a vehicle traveling on mars. the shortest distance between earth and mars is 56 * 106 km; the longest is 400 * 106 km. what is the delay time for the signal that you send to mars from earth? can you use radio signals to give commands to the vehicle?

Answers

The delay time for the signal that you send to mars from earth is 22.4 minutes.

The delay time for a signal sent from Earth to Mars depends on the distance between the two planets and the speed of light, which is approximately 299,792 km/s. Using the shortest distance of 56 * 10⁶km, the delay time would be approximately 187 seconds, or just over 3 minutes. Using the longest distance of 400 * 10⁶ km, the delay time would be approximately 22.4 minutes. Radio signals can be used to send commands to the vehicle on Mars, but the delay time must be taken into account.

This delay can make real-time communication with the vehicle difficult, so some form of autonomous or pre-programmed control may be necessary. Additionally, the distance between Earth and Mars can vary depending on the relative positions of the two planets, so the delay time can also vary. However, despite these challenges, radio communication remains a vital tool for sending commands and receiving data from spacecraft on Mars and other distant locations in the solar system.

To know more about the Distance, here

https://brainly.com/question/13046933

#SPJ4


4. 2 Water vapour is a gas. Explain the difference and similarities between water in the vapour
form and in the liquid form in terms of the kinetic molecular theory (KMT). ​

Answers

The kinetic molecular theory (KMT) describes the behavior of particles in a substance.

According to KMT, particles in both water vapor and liquid water are in constant motion and have kinetic energy. However, the particles in water vapor have more kinetic energy than those in liquid water because they are at a higher temperature.

As a result, the particles in water vapor are farther apart and have a higher average speed than the particles in liquid water. Additionally, water vapor and liquid water have different arrangements of particles.

In water vapor, the particles are not closely packed and are free to move, while in liquid water, the particles are tightly packed and have less freedom of movement.

To know more about kinetic molecular theory, refer here:

https://brainly.com/question/15013597#

#SPJ11

You can hold a box against a rough wall and prevent it from slipping doen by pressing hard horizontally. if the coefficient os static friction is 0.35 and the box has a mass of 14.2 kg, what minimum force f will keep thebox from falling

Answers

The minimum force required to keep the box from falling is 48.71 N.

The minimum force required to keep the box from falling can be calculated using the formula F = μsN, where F is the minimum force required, μs is the coefficient of static friction, and N is the normal force acting on the box.

In this case, the normal force is equal to the weight of the box, which can be calculated using the formula N = mg,

where m is the mass of the box and g is the acceleration due to gravity.

Thus, N = 14.2 kg x 9.8 m/s^2 = 139.16 N.

Substituting the values into the formula,

we get F = 0.35 x 139.16 N = 48.71 N.

Therefore, a minimum force of 48.71 N is required to prevent the box from falling.

This force is determined by the coefficient of static friction and the weight of the box. The coefficient of static friction is a measure of the friction between two surfaces that are not moving relative to each other, while the weight of the box is a measure of the force due to gravity acting on the box.

To know more about the Static friction, here

https://brainly.com/question/28940591

#SPJ4

A speeding car traveling at 41 m/s passes a parked police car. One second after getting passed, the police car begins pursuit. The police car accelerates at a rate of 7.5 m/s/s. The police car catches up after 12.8 seconds and the police car travels 527 meters.

What is the velocity of the police car when it catches up to the speeding car?

Answers

Answer:

To solve this problem, we can use the equation:

distance = initial velocity x time + 1/2 x acceleration x time^2

First, we need to find the initial distance between the two cars. The speeding car travels for 1 second before the police car begins pursuit, so its initial distance from the parked police car is:

initial distance = 41 m/s x 1 s = 41 m

Now we can use the equation to find the time it takes for the police car to catch up to the speeding car:

distance = initial velocity x time + 1/2 x acceleration x time^2

527 m = 0 m/s x t + 1/2 x 7.5 m/s^2 x t^2

Simplifying:

t = sqrt((2 x 527 m) / 7.5 m/s^2) = 12.92 s

So the police car catches up to the speeding car after 12.92 seconds. Now we can use the equation:

final velocity = initial velocity + acceleration x time

to find the velocity of the police car when it catches up to the speeding car:

final velocity = 0 m/s + 7.5 m/s^2 x 12.92 s = 96.9 m/s

Therefore, the velocity of the police car when it catches up to the speeding car is 96.9 m/s.

Explanation:

If three crests pass Pin in one second, the wavelength is?

Answers

The wavelength of the wave as we have it is 3m

What is the wavelength of a wave?

A wave's wavelength is the separation between two successive locations on the wave that are in phase, or at the same stage of their cycle. In other terms, it is the separation between two wave crests or troughs.

We know that the wavelength = Number of crests = 3m

Wave speed = 3 m/s

We would then have that;

v = λf

v = wave speed

f = frequency

λ = wavelength

Thus since there are three crests then the wavelength must be 3m

Learn more about wavelength:https://brainly.com/question/31143857

#SPJ1

What type of reaction is being shown in this energy diagram?
Energy
Reactants
to
Activation
Energy
ħ₁.
Products
Time

Answers

Answer: thermodynamics energy

Which two statements describe what happens to the nuclei of atoms during a fusion reaction

Answers

During a fusion reaction, two statements that describe what happens to the nuclei of atoms are A small amount of mass in the nuclei that combine is converted to energy and Nuclei with small masses combine to form nuclei with larger masses.​ The correct option is B and D.


A small amount of mass in the nuclei that combine is converted to energy. During the fusion reaction, when the smaller nuclei combine, a small amount of mass is converted into a significant amount of energy, as described by Einstein's famous equation E=mc². This energy release is what makes fusion reactions so powerful and a potential source of clean energy.

Nuclei with small masses combine to form nuclei with larger masses. In a fusion reaction, lighter nuclei, typically isotopes of hydrogen like deuterium and tritium, combine under high pressure and temperature to form larger nuclei, such as helium. This process is what powers the Sun and other stars, as they fuse hydrogen into helium, releasing energy in the form of light and heat. The correct option is B and D.

To know more about fusion reaction, refer here:

https://brainly.com/question/2554334#

#SPJ11

Complete question:

Which two statements describe what happens to the nuclei of atoms during a fusion reaction?

A. Large nuclei break apart into two or more smaller nuclei.

B. A small amount of mass in the nuclei that combine is converted to energy.

C. Each nucleus formed has fewer protons than each original nucleus had.

D. Nuclei with small masses combine to form nuclei with larger masses.​

a thin wire lies along the curve given by r(t) = cos(t), 0, sin(t) , 0 ≤ t ≤ , and has mass density (x, y, z) = 4 − z kg/m3. find the total mass and the center of mass of the wire. m _____ kg

Answers

To find the total mass of the wire, we need to integrate the mass density over the length of the wire. The length of the wire is given by:

L = ∫₀^π ∥r'(t)∥ dt

where r(t) = (cos(t), 0, sin(t)) is the position vector of the wire at time t, and ∥r'(t)∥ is the magnitude of the velocity vector.

r'(t) = (-sin(t), 0, cos(t)) so ∥r'(t)∥ = sqrt(sin²(t) + cos²(t)) = 1

Therefore, L = ∫₀^π 1 dt = π.

What is the total mass and the center of mass of the wire?

Now, to find the mass, we need to integrate the mass density over the length of the wire:

m = ∫₀^π (4 - z) ∥r'(t)∥ dt

Since z = sin(t), we have:

m = ∫₀^π (4 - sin(t)) dt

Using the substitution u = cos(t), du = -sin(t) dt, we can write:

m = ∫₁^-1 (4 - √(1 - u²)) du

This integral can be evaluated using standard techniques, or with the help of a computer algebra system, to get:

m = 8.

To find the center of mass, we need to compute the weighted average of the position vector r(t), using the mass density as the weight function:

CM = (1/m) ∫₀^π r(t) (4 - sin(t)) ∥r'(t)∥ dt

= (1/8) ∫₀^π (cos(t), 0, sin(t)) (4 - sin(t)) (1) dt

= (1/8) ∫₀^π (4 cos(t) - sin(t) cos(t), 0, 4 sin(t)) dt

= (1/8) (8, 0, 0)

= (1, 0, 0)

Therefore, the total mass of the wire is 8 kg, and its center of mass is located at (1, 0, 0).

Learn more about  mass of the wire from

https://brainly.com/question/28496633

#SPJ1

A force compresses a bone by 1. 0 mm. A second bone has the same cross-sectional area but twice the length as the first. By how much would the same force compress this second bone

Answers

The second bone has the same cross-sectional area and material as the first bone, the same force would create the same stress in both bones.

To solve this problem, we need to consider the relationship between stress, strain, and Young's modulus. Stress is the force applied divided by the cross-sectional area, strain is the change in length divided by the original length, and Young's modulus is a material property that relates stress and strain.

1. Calculate stress (σ) for the first bone:
σ = Force / Cross-sectional area

2. Calculate strain (ε) for the first bone:
ε = Compression / Original Length
ε = 1.0 mm / Original Length

3. Find Young's modulus (Y) for the bone material:
Y = σ / ε

4. Calculate the strain (ε') on the second bone, using the same force and Young's modulus:
ε' = σ / Y

5. Calculate the compression (ΔL) of the second bone, given that its length is twice the first bone:
ΔL = ε' * (2 * Original Length)

However, since the second bone is twice as long, it would experience a greater strain and, as a result, a larger compression. By calculating the compression of the second bone using the relationship between stress, strain, and Young's modulus, you can determine how much the same force would compress the second bone.

For more about cross-sectional area:

https://brainly.com/question/20532494

#SPJ11

Running with an initial velocity of 10.2 m/s m / s , a horse has an average acceleration of -1.77 m/s2 m / s 2 . how much time does it take for the horse to decrease its velocity to 6.1 m/s m / s ?

Answers

It takes approximately 2.32 seconds for the horse to decrease its velocity to 6.1 m/s.

Using the given terms, we can solve the problem using the formula for acceleration:

a = (v_f - v_i) / t

Where:
a = -1.77 m/s² (average acceleration)
v_i = 10.2 m/s (initial velocity)
v_f = 6.1 m/s (final velocity)
t = time (which we need to find)

Rearranging the formula to solve for time:

t = (v_f - v_i) / a

Substituting the given values:

t = (6.1 m/s - 10.2 m/s) / (-1.77 m/s²)
t = (-4.1 m/s) / (-1.77 m/s²)

Now, calculating the time:

t ≈ 2.32 seconds

It takes approximately 2.32 seconds for the horse to decrease its velocity to 6.1 m/s.

To learn more about velocity, refer below:

https://brainly.com/question/17127206

#SPJ11

An electron traveling with speed v around a circle of radius r is equivalent to a current of:


evr/2


ev/r


ev/2πr


2πer/v


2πev/r

Answers

The current of an electron traveling with speed v around a circle of radius r is equivalent to ev/(2πr).

An electron traveling with speed v around a circle of radius r is equivalent to a current. To calculate the current, we need to consider the charge of an electron (e) and the time it takes for one complete revolution (T).

First, find the circumference of the circle (C):
C = 2πr

Next, calculate the time for one revolution (T) by dividing the circumference by the speed of the electron:
T = C/v = (2πr)/v

Now, we know that current (I) is defined as the charge (Q) passing through a conductor per unit time (t):
I = Q/t

Since there's only one electron, the charge Q is simply the charge of an electron (e). Substitute the values of Q and T in the formula:

I = e/T = e/[(2πr)/v]

Simplify the expression:
I = ev/(2πr)

For more about electron traveling:

https://brainly.com/question/29480785

#SPJ11

physicist s. a. goudsmit devised a method for measuring accurately the masses of heavy ions by timing their periods of revolution in a known magnetic field. a singly charged ion makes 6.00 rev in a 40.0 mt in 1.32 ms. calculate its mass, in atomic mass units.

Answers

A singly charged ion makes 6.00 rev in a 40.0 mt in 1.32 ms. The atomic mass of the singly charged ion is 24.3 atomic mass units

Physicist S.A. Goudsmit devised a method for accurately measuring the masses of heavy ions by timing their periods of revolution in a known magnetic field. This method is known as the magnetic moment method. It involves the use of a magnetic field to deflect the ion in a circular path, and measuring the time it takes for the ion to complete a full revolution. The mass of the ion can then be calculated from its charge, the magnetic field strength, and the time taken for one revolution.

In this case, we are given that a singly charged ion makes 6.00 revolutions in a magnetic field of 40.0 millitesla in 1.32 milliseconds. To calculate its mass in atomic mass units (amu), we can use the formula:

mass = (charge x magnetic field x period) / (2 x pi)

where charge is the charge of the ion (in Coulombs), magnetic field is the strength of the magnetic field (in Tesla), period is the time taken for one revolution (in seconds), and pi is the mathematical constant pi.

Since the ion is singly charged, its charge is 1.6 x 10^-19 C. Converting the magnetic field from millitesla to Tesla, we get 0.04 T. Converting the period from milliseconds to seconds, we get 0.00132 s. Plugging in these values, we get:

mass = (1.6 x 10^-19 C x 0.04 T x 0.00132 s) / (2 x pi) = 4.04 x 10^-26 kg

To convert this mass to atomic mass units, we divide by the mass of one atomic mass unit (1.66 x 10^-27 kg/amu):

mass in amu = (4.04 x 10^-26 kg) / (1.66 x 10^-27 kg/amu) = 24.3 amu

To learn more about : mass
https://brainly.com/question/86444

#SPJ11

Bina goes downstairs to her basement, does 20 pushups and 20 squats, and then returns upstairs. which of these activities involves concentric contractions?

Answers

These activities involves concentric contractions: doing pushups and doing squats. The correct option is B and D

Concentric contractions occur when a muscle shortens as it generates force. In Bina's case, both doing pushups and doing squats involve concentric contractions. When she performs pushups, the concentric phase occurs as she pushes her body up from the ground, causing her chest and triceps muscles to shorten.

Similarly, when doing squats, the concentric contraction happens when she rises from the squat position, causing her quadriceps and gluteal muscles to shorten. On the other hand, going downstairs  and going upstairs  mainly involve eccentric contractions, where the muscle lengthens while generating force.

To know more about concentric contractions, refer here:

https://brainly.com/question/15048619#

#SPJ11

Complete question:

Bina goes downstairs to her basement, does 20 pushups and 20 squats, and then returns upstairs. which of these activities involves concentric contractions?

a. going downstairs

b. doing pushups

c. going upstairs

d. doing squats

Can people get the flu from a flu vaccine explain your answer

Answers

It is not possible to get the flu from a flu vaccine. The flu vaccine is made from either weakened or dead flu viruses, which are not strong enough to cause the flu. In some cases, people may experience mild side effects after getting the flu vaccine, such as a low-grade fever or muscle aches. These side effects are normal and are not the same as getting the flu.

If a cannonball were launched from the surface of Earth, it would eventually fall to the ground. However, if the cannonball was moving fast enough, it would move forward fast enough that it would never fall all the way to the ground, as shown in the animation. If the cannonball in the diagram were launched even faster, what would happen to its motion?

Answers

If a cannonball were launched from the surface of Earth at an even faster speed: its motion would be significantly impacted.

As the cannonball's speed increases, it would move forward more quickly, causing the rate at which it falls towards the ground to be countered by its horizontal motion. If the cannonball reaches a critical speed known as the "orbital velocity," it will enter a stable orbit around the Earth. In this state, the cannonball's forward motion will balance the force of gravity, preventing it from falling back to the ground.

Instead, it will continuously travel around the Earth in a circular or elliptical path. If the cannonball were to be launched at an even higher speed, beyond the escape velocity, it would eventually break free from Earth's gravitational pull and continue moving away from our planet, potentially entering into an orbit around another celestial body or traveling through space indefinitely.

To know more about motion, refer here:

https://brainly.com/question/29255792#

#SPJ11

How do you fix the sims 4 walking glitch? Whenever I out on cc, it either dissapears when I start the game, or the clothing moves weirdly with the sim

Answers

The walking glitch in The Sims 4 when using custom content (CC) can be caused by several factors, including outdated or incompatible CC or conflicts between different CC items.

One solution is to ensure that all CC is up to date and compatible with the current version of the game. It is also important to check for any conflicts between CC items, as some items may not work well together.

Additionally, deleting the localthumbcache.package file in the game directory and repairing the game through Origin may help resolve the issue.

If the issue persists, removing or disabling the problematic CC may be necessary.

To know more about The Sims, refer here:

https://brainly.com/question/1347588#

#SPJ11

What do you measure when you find a substance’s temperature?

Answers

Answer:

The Average kinetic Energy of all the atoms and molecules of substance

Explanation:

You would measure the kinetic energy of the atoms or molecules in the system.

I hope that this helps

Titan, with a radius of 2. 58 x 10^6 m, is the largest moon of the planet Saturn. If the mass of Titan is 1. 35 x10^23 kg, what is the acceleration due to gravity on the surface of this moon?

A. 1. 35 m/s^2
B. 3. 49 m/s^2
C. 3. 49 x 10^6 m/s^2
D. 1. 35 x 10^6 m/s^2

Answers

The acceleration due to gravity on the surface of Titan can be calculated using the formula g = GM/[tex]R^{2}[/tex], where G is the gravitational constant, M is the mass of the moon, and R is the radius of the moon. Therefore, the correct answer is B.

Plugging in the given values, we get g = (6.67 x [tex]10^{-11}[/tex] [tex]Nm^{2}/kg^{2}[/tex])(1.35 x [tex]10^{23}[/tex] kg)/[tex](2.58* 10^{6}m)^{2}[/tex] = 3.49 [tex]m/s^{2}[/tex].

This means that an object on the surface of Titan would experience a gravitational acceleration of 3.49 [tex]m/s^{2}[/tex], which is about one-seventh of the acceleration due to gravity on Earth.

To know more about gravitational acceleration, refer here:

https://brainly.com/question/30429836#

#SPJ11

What is the torque exerted by the wrench in scenario c?

What is the torque exerted by the wrench in scenario d?

If you've figured out all of the torques correctly, then you can clearly see that the scenario with the highest torque is:

Answers

The torque exerted by the wrench in scenario (c) and (d) is 'LF'. The torque exerted by the wrench in all the four scenario are same, so there is no such scenario of having the highest torque.

We know, Torque is the cross product of radius vector and force vector. It is defined as turning force that tends to cause rotation around any axis. It is also referred to as the 'Moment of Force'.

Mathematically,

Torque, ζ = r × F = r F sinθ

In case (a.),

The force vector is perpendicular to the radius vector (or the length) i.e., θ = 90°

∴ ζ = r × F = L × F = LF

In case (b.)

F is at an angle with horizontal, then only the vertical component of force that is 2Fsinθ will contribute to the torque.

∴  ζ = r × 2Fsin30° = L × 2F × (1/2) = LF

In case (c.),

The force vector is perpendicular to the radius vector i.e., θ = 90°

∴  ζ = r × F = 2L × (F/2) = LF

In case (d.),

Again the force vector is perpendicular to the radius vector (or the length) i.e., θ = 90°

∴  ζ = r × F = (L/2) × 2F = LF

Therefore, torque exerted by wrench in all scenario is same i.e., LF.

Learn more about torque here

brainly.com/question/31248352

#SPJ1

A ball drops some distance through the air, gaining 20 j of kinetic energy while experiencing some air resistance. how much gravitational potential energy did the ball lose

Answers

The ball lost gravitational potential energy equal to the amount of kinetic energy it gained while falling, but some of that energy was dissipated due to air resistance.

When an object falls from a height, its potential energy is converted into kinetic energy. In this case, the ball gains 20 J of kinetic energy while falling, indicating that it has lost an equivalent amount of potential energy due to gravity.

However, the presence of air resistance complicates the situation. As the ball falls, it experiences a force opposing its motion due to the air molecules it collides with. This force causes some of the ball's energy to be dissipated in the form of heat, sound, and other forms of energy.

Therefore, to determine how much gravitational potential energy the ball lost, we need to take into account the amount of energy that was dissipated by air resistance. This is difficult to quantify without additional information about the ball's mass, velocity, and the nature of the air resistance it experienced.

In summary, the ball lost gravitational potential energy equal to the amount of kinetic energy it gained while falling, but some of that energy was dissipated due to air resistance. The exact amount of energy lost to air resistance would require additional information and calculations.

To know more about potential energy refer here:

https://brainly.com/question/30672627#

#SPJ11

A 30 kg block with velocity 50 m/s is encountering a constant 8 N friction force. What is the momentum of the block after 15 seconds?

Answers

The momentum of a 30 kg block with an initial velocity of 50 m/s encountering a constant 8 N friction force and traveling for 15 seconds is 1680 kg m/s.

The initial momentum of the block is given by:

p = mv = (30 kg) x (50 m/s) = 1500 kg m/s

The net force acting on the block is given by the force of friction:

[tex]F_{net} = F_{friction} = 8 N[/tex]

Using Newton's second law, we can find the acceleration of the block:

[tex]F_{net} = ma[/tex]

8 N = (30 kg) a

[tex]a = 8/30 m/s^2[/tex]

Using the equation for displacement with constant acceleration, we can find the distance traveled by the block during the 15 seconds:

[tex]d = vt + 1/2 at^2[/tex]

[tex]d = (50 m/s)(15 s) + 1/2 (8/30 m/s^2)(15 s)^2[/tex]

d = 750 m + 450 m = 1200 m

Finally, using the equation for final velocity with constant acceleration, we can find the final velocity of the block:

[tex]v_{f^2} = v_{i^2} + 2ad[/tex]

[tex]v_{f^2} = (50 m/s)^2 + 2(8/30 m/s^2)(1200 m)[/tex]

[tex]v_{f^2} = 2500 \;m^2/s^2 + 640 \;m^2/s^2 = 3140\; m^2/s^2[/tex]

[tex]v_f[/tex] = 56.0 m/s

Therefore, the momentum of the block after 15 seconds is:

p = mv = (30 kg)(56.0 m/s) = 1680 kg m/s

In summary, the momentum of a 30 kg block with an initial velocity of 50 m/s encountering a constant 8 N friction force and traveling for 15 seconds is 1680 kg m/s.

To know more about velocity refer here:

https://brainly.com/question/19979064#

#SPJ11

27. A bicycle wheel on a repair bench can be


accelerated either by pulling on the chain that


is on the gear or by pulling on a string wrapped


around the tire. The tire's radius is 0. 38 m, while


the radius of the gear is 0. 14 m. What force would


you need to pull on the string to produce the


same acceleration you obtained with a force of


15 N on the chain?

Answers

You would need to pull on the string with a force of 5.76 N to produce the same acceleration you obtained with a force of 15 N on the chain.

To calculate the force needed to produce the same acceleration as a force of 15 N on the chain, we need to use the formula:
force = mass × acceleration

First, we need to calculate the acceleration of the bicycle wheel when a force of 15 N is applied to the chain. We can use the formula:
acceleration = [tex]\frac{acceleration}{mass}[/tex]
Assuming the mass of the wheel is negligible, we can simplify this to:
acceleration = [tex]=\frac{force}{0.38}[/tex] = [tex]\frac{15N}{0.38}[/tex]=39.47 N/m

Now we can calculate the force needed to produce the same acceleration when pulling on the string wrapped around the tire. We can use the formula:
force = mass × acceleration
The mass of the wheel does not change, so we can use the same acceleration value we calculated earlier. However, the radius of the tire is different from the radius of the gear, so we need to take this into account.

The circumference of the tire is 2π(0.38 m) = 2.39 m, while the circumference of the gear is 2π(0.14 m) = 0.88 m.

This means that the force needed to produce the same acceleration when pulling on the string is:
force = mass × acceleration × [tex](\frac{radius of the gear}{radius of the tire} )[/tex]
= 0.38 kg x 39.47 N/m x [tex](\frac{0.14 m}{0.38 m} )[/tex]
= 5.76 N

To know more about the different types of forces visit:

https://brainly.com/question/13191643

#SPJ11

6.
a certain ball was measured to have a momentum of 38 kg•m/s when traveling at 8m/s, how much mass does this ball contain?
а.
304 kg
b
5 lb
304 ib
d
4.75 kg

Answers

The ball contains 4.75 kg of mass. To solve this question we will use the formula of momentum, that is, p=mv

To answer this question, we can use the formula for momentum:

p = mv

where p is the momentum, m is the mass, and v is the velocity.

We are given that the ball has a momentum of 38 kg•m/s when travelling at 8m/s. Therefore, we can plug in these values and solve for m:

38 kg•m/s = m * 8 m/s

To solve for m, we can divide both sides by 8 m/s:

m = 38 kg•m/s / 8 m/s

Simplifying this expression, we get:

m = 4.75 kg

Therefore, the ball contains 4.75 kg of mass.

Know more about momentum here:
https://brainly.com/question/30677308

#SPJ11

Gravity is also affected by mass. ____, which is the amount of matter in an object. As the amount of mass increases, the forces of gravity between two objects _____

Please help

Answers

Answer:

Mass

Increases

Explanation:

Gravity is also affected by mass. Mass, which is the amount of matter in an object. As the amount of mass increases, the forces of gravity between two objects also increases.

A 2.0 kg brick has the dimensions 7.5 cm x 15 cm x 30cm. find the pressures exerted by the brick on a table when it is resting on its various faces.

Answers

When the brick is resting on its top face, the pressure is also 174 kPa. When the brick is resting on one of its long faces, the pressure exerted is  218 kPa. When the brick is resting on one of its short faces, the pressure is 392 kPa.

The pressure exerted by an object on a surface is defined as the force per unit area perpendicular to the surface. In this case, we can calculate the pressure exerted by the brick on the table when it is resting on each of its faces using the formula P = F/A, where F is the force exerted by the brick and A is the area of the face.

When the brick is resting on its bottom face, the area is 0.1125 m², and the force exerted by the brick is its weight, which is 19.6 N. Therefore, the pressure exerted is P = 19.6 N / 0.1125 m² = 174 kPa.

Similarly, when the brick is resting on its top face, the pressure is also 174 kPa.

When the brick is resting on one of its long faces, the area is 0.045 m², and the force exerted is 9.8 N. Therefore, the pressure exerted is P = 9.8 N / 0.045 m² = 218 kPa.

When the brick is resting on one of its short faces, the pressure is the same as when it is resting on the other short face, which is 392 kPa.

In summary, the pressure exerted by the brick on the table varies depending on which face is in contact with the table, with the highest pressure of 392 kPa being exerted when the brick is resting on one of its short faces.

To know more about pressure refer here:

https://brainly.com/question/28907914#

#SPJ11

To find the pressure exerted by the brick on a table when it is resting on its various faces, we can use the formula:

Pressure = Force / Area

The force exerted by the brick is equal to its weight, which can be calculated using the formula:

Weight = mass * gravity

Where:

mass = 2.0 kg (mass of the brick)

gravity = 9.8 m/s² (acceleration due to gravity)

First, let's calculate the area of each face of the brick:

Face 1 (7.5 cm x 15 cm):

Area1 = 7.5 cm * 15 cm

Face 2 (7.5 cm x 30 cm):

Area2 = 7.5 cm * 30 cm

Face 3 (15 cm x 30 cm):

Area3 = 15 cm * 30 cm

Now, let's calculate the pressures exerted by the brick on the table when it is resting on each face:

Pressure1 = Weight / Area1

Pressure2 = Weight / Area2

Pressure3 = Weight / Area3

Substituting the values into the formulas:

Pressure1 = (2.0 kg * 9.8 m/s²) / (7.5 cm * 15 cm)

Pressure2 = (2.0 kg * 9.8 m/s²) / (7.5 cm * 30 cm)

Pressure3 = (2.0 kg * 9.8 m/s²) / (15 cm * 30 cm)

Now you can calculate the values for Pressure1, Pressure2, and Pressure3. Remember to convert the units to the appropriate form (e.g., meters for length and pascals for pressure) for consistency.

To know more about pressure refer here

https://brainly.com/question/12971272#

#SPJ11

let us recall what is a magnet? How does it work?

Answers

Answer:

The magnets are surrounded by an invisible magnetic field that contains stored-up, or potential, energy. When attempting to push two like-sided poles together, the stored-up energy becomes movement, or kinetic energy, and forces them apart. The same principle happens when two unlike poles come together.

The fact that the galaxies are rotating at about the same velocity from the center to the edge as opposed to faster near the centers is evidence that.
a. There must be more gravity than that calculated from normal Mass
b. They are rotating slower over time
c. Dark energy is pulling on them
d. They are measuring the velocities incorrectly ​

Answers

The fact that galaxies are rotating at about the same velocity from the center to the edge, as opposed to faster near the centers, is evidence that there must be more gravity than that calculated from normal mass.

This observation suggests the presence of dark matter, which contributes to the overall gravitational force in galaxies.

However, observations have shown that the rotation curves of many galaxies remain nearly flat, indicating that the orbital velocities do not decrease as expected.

Instead, they remain roughly constant or increase slightly with distance from the galactic center. This phenomenon is often referred to as the "galaxy rotation problem."

To account for these unexpected rotation curves, astronomers have proposed the existence of dark matter. Dark matter is a hypothetical form of matter that does not interact with light or other forms of electromagnetic radiation, making it invisible and difficult to detect directly.

It is thought to be present in large quantities throughout the universe, including within galaxies.

The presence of dark matter can explain the observed rotation curves because it contributes additional gravitational force to galaxies. This extra gravity from the dark matter allows stars and gas to orbit at higher velocities, even at larger distances from the galactic center.

In other words, the gravitational pull from the combined normal matter (stars, gas, etc.) and dark matter is what keeps the rotation curves flat or rising.

To learn more about universe, refer below:

https://brainly.com/question/9724831

#SPJ11

A pen contains a spring with a constant of 216 N/m. When the tip of the pen is in its retracted position, the spring is compressed 4.10 mm from its unstrained length. In order to push the tip out and lock it into its writing position, the spring must be compressed an additional 6.10 mm. How much work is done by the spring force to ready the pen for writing? Be sure to include the proper algebraic sign with your answer.

Answers

Answer:The spring force is conservative, so the work done by the spring force is equal to the negative of the potential energy stored in the spring:

U = -1/2 k x^2

where k is the spring constant and x is the displacement from the unstrained length.

The initial compression of the spring is 4.10 mm = 0.00410 m, and the additional compression is 6.10 mm = 0.00610 m. The total compression of the spring is therefore x = 0.00410 m + 0.00610 m = 0.0102 m.

The potential energy stored in the spring when it is compressed by a distance x is:

U = -1/2 k x^2

Substituting the given values, we get:

U = -1/2 (216 N/m) (0.0102 m)^2

U = -0.0112 J

The work done by the spring force to ready the pen for writing is equal to the change in potential energy:

W = U_final - U_initial

where U_initial is the potential energy of the spring when it is compressed 4.10 mm, and U_final is the potential energy of the spring when it is compressed an additional 6.10 mm.

U_initial = -1/2 (216 N/m) (0.00410 m)^2 = -0.000090 J

U_final = -1/2 (216 N/m) (0.0102 m)^2 = -0.0112 J

W = U_final - U_initial

W = (-0.0112 J) - (-0.000090 J)

W = -0.0111 J

The negative sign indicates that the work done by the spring force is done on the pen (i.e. the pen gains potential energy), consistent with our intuition that the spring force is providing the energy needed to push the pen tip out and lock it into place. Therefore, the proper algebraic sign for the work done by the spring force is negative.

Explanation:

As you've learned, several phrases can be used to describe wave motion. Such
phrases include how often, how much time, how fast, how high, and how long.
Which of these phrases would be the most appropriate phrase for describing the period of a wave?​

Answers

Out of the various phrases used to describe wave motion, the most appropriate phrase for describing the period of a wave would be "how often."

The period of a wave refers to the time it takes for one complete cycle of the wave to occur. This means that it measures how often the wave completes its cycle.

Therefore, "how often" is the most relevant phrase to use when describing the period of a wave.

It's important to note that the other phrases mentioned - how much time, how fast, how high, and how long - are all relevant to different aspects of wave motion.

"How much time" is related to the duration of the wave, "how fast" refers to the speed at which the wave travels, "how high" refers to the amplitude of the wave, and "how long" can refer to both the duration and the length of the wave.

Understanding the various phrases used to describe wave motion is important for accurately communicating information about waves.

When discussing waves, it's essential to use the appropriate terminology to ensure that the content loaded is clear and precise.

To know more about wave motion refer here

https://brainly.com/question/12512349#

#SPJ11

the horizontal surface which the 1 block of mass 2kg slides frictionless the force of 29N acts on the block in a horizontal direction and the force of 87 N acts on the block at an angle as shown what is the magnitude of the resulting acceleration of the block (1) 5 (2) 2.2549 (3) 4.5 (4) 3.63636 (5) 5.90909(6) 6.89819 (7) 2.75 (8) 14.5455 (9)7.25 (10) 4.10714

Answers

The magnitude of the resulting acceleration of the block is (8), 14.5455 m/s²

How to determine magnitude?

Use Newton's second law to solve this problem:

ΣF = ma

where ΣF = net force acting on the block, m = mass of the block, and a = acceleration of the block.

Resolve the force of 87 N into its horizontal and vertical components.

F_horizontal = F cosθ = 87 cos 30° = 75.366 N

F_vertical = F sinθ = 87 sin 30° = 43.5 N

The net force in the horizontal direction is:

ΣF_horizontal = 29 N

Using ΣF = ma, find the acceleration:

a = ΣF / m = 29 N / 2 kg = 14.5 m/s²

Therefore, the magnitude of the resulting acceleration of the block is:

a = 14.5 m/s²

The answer is (8) 14.5455, which rounds to 14.5 m/s².

Find out more on magnitude here: https://brainly.com/question/30337362

#SPJ1

Other Questions
If muscular endurance is your primary training goal, what variations would you choose for push-ups? Explain yourthinking. And If muscular strength and muscular enduranc& were equally important to you, what variation(s) would you choose fosquats? Explain your thinking Is Chuukese a dying language? Trends in supply management include: Group of answer choices increasing the number of suppliers and developing closer relationships. Limiting the number of suppliers and focusing on results from key suppliers. Switching suppliers frequently through online auctions to get price discounts. Greater concentration of the supplier selection decision in procurement. Negotiating shorter term contracts with fewer suppliers to increase leverage (-6,-4), (0, -4), and (2,-4)What is the equation of this line? Write the net chemical equation for the production of manganese from manganese (II) carbonate, oxygen and aluminum. Be sure your equation is balanced. MAKRING BRAINLIST ^_^ "Twisted till" and "claw curled" are example of what poetic device1) Repetition 2) Alilteration 3) Ryhme4) Onomatopoeia Author repeats "hands folded in as if he wished for something" because it1) Encourages the readers to save a creature 2) Exaggerates the praying mantis's movement 3) Compares the author to the praying mantis 4) Makes the praying mantis seem more human 4. Which set of data could be represented by the box-and-whisker plot? (1 point)O0, 3, 9, 9, 11, 14, 15, 16, 16, 18, 19, 25, 25, 28, 28, 30O2, 3, 4, 7, 13, 15, 15, 15, 16, 17, 20, 22, 25, 25, 26, 28O2, 6, 7, 8, 10, 11, 12, 14, 18, 20, 22, 24, 26, 27, 27, 28O2, 2, 7, 10, 10, 11, 13, 15, 17, 20, 20, 24, 26, 27, 27, 28 What happened to the deer population since the wolves have returned? According to the text, Direct Democracy used in ancient civilizations didn't make sense to the U.S. founding fathers. Therefore - a. they created a democracy in which the citizens elect others to represent them. b. they wrote three drafts of the United States' Constitution to ensure freedom. c. the Bill of Rights was created in order for the citizens to have all the voting power. Forests are complex, evolving ecosystems. Forinstance, pioneer tree species can be displaced by successional species better adaptedto the changing environment. Ecologists mapped a large Canadian forest plotdominated by Douglas fir with an understory of western hemlock and western red cedar.Sapling trees (young trees shorter than 1.3 meters) are indicative of the future of aforest. The 246 sapling trees recorded in this sample forest plot were of the followingtypes:Are there equal proportions of RC, DF, and WH among sapling trees in this forest?1. State your null and alternative hypothesis. (10 points)2. Report appropriate test statistics and p-value. (20 points)3. With alpha=0.05, state your conclusion. (10 points)4. Investigate components of your test statistics. What does your analysis suggestabout this forests successional stage? (10 points) The Really Big Dam is 1000 feet wide, holds back a depth of 60 feet of water, and the lake behind the dam extends back one quarter of a mile. The Very Big Dam is also 1000 feet wide, holds back a depth of 50 feet of water, and the lake behind the dam extends back for 2 miles. If the dams were constructed in the same way, which dam had to be constructed to be strongest? (Assume the water levels do not vary seasonally. ) 5 37 ( 1 Consider 9 g(x) = $/ +31 + (2x +39 3 3 A) 57-2 +6(2t - 1)* calculate g(x) g) B) 5 3r 3(2x - 1) 5 C) 3 3(2x - 1) 3 D) +6(2t - 1) which of the following statements is true?multiple choicethe body stores vitamins in the liver, spleen, and bones.most vitamins cannot be synthesized by the human body.the body excretes fat-soluble vitamins more easily than water-soluble vitamins.vitamins supply about 2 kcal per gram. HOH14----IList the number of each atom in the formulas above:H -----LI DONE H-----II H 1 minute speech on the topic PATIENCE IS A PLASTER FOR ALL SORES Ms. Regan is making a circular quilt and wants to include a lace patternaround the outside of the quilt. If the area of the quilt is 28. 26 square feet, how many feet of lace does Ms. Regan need to purchase? (Use 3. 14 for pi. ) please help................ the probability that a student takes algebra two is 8%. The probability that a student who is taking algebra two will also be taking chemistry is 17%. what is the probability that a randomly selscted student will take both algebra two and chemistry? In circle K with \text{m} \angle JKL= 90mJKL=90, find the \text{m} \angle JMLmJML i need help with project i dont know how to code and it is a console application using c#